Filter
Top Products
Index
GFK-0825F Index Index-3
configuration format for datagram, 8-10, 8-27
Genius systems with Field Control, 1-7
Grounding, C-11
BIU Terminal Block, 3-9
system, 3-4
Group Data, 4-6
BIU reads from other modules, 4-5
Group Data moves, 4-4
Group Data Moves
configuration, D-4, D-6
configuring, 5-102
H
Hand-held Monitor
used to clear faults, 6-3
used to monitor I/O data, 7-3
Hand-held Monitor Connector, 3-2
Hand-held Monitor
attaching to BIU for configuration, 5-3
connector on BIU, 2-1
version required with Field Control, 1-9
HHM Menus for Field Control, 5-5
Hold Last State/Default
Analog input module, 5-34
Analog output Module, 5-36
Discrete input module, 5-23
discrete output module, 5-25, 5-27, 5-28
Host computer, 1-7
handles input data from BIU, 4-10
I/O service, 7-7
Host CPU, 1-7
Hot Insertion, 2-7
Hot standby redundancy, 1-10, 5-12
Humidity specification, 1-5
I
I/O data
forcing, 7-2, 7-5
handling, 7-2
override, 7-2, 7-6
transfer with host, 4-9
I/O Fault Table at PLC, 6-5
I/O Map, 4-2
configuring data for the BIU, 5-16
I/O memory, 4-2
I/O module
elete configuration, 5-21
I/O modules
introduction, 1-3
locations for, 3-5
read ID with HHM, 5-21
I/O references
Analog Grouped Input module, 5-40, 5-48, 5-56,
5-90
Analog input module, 5-29
Analog Voltage Output module, 5-81
discrete input module, 5-22
discrete output module, 5-24, 5-26
for analog output module, 5-35
Micro Field Processor's internal, 4-14
RTD module, 5-64
Thermocouple module, 5-72
I/O scanning
enable/disable, 5-15
I/O Table display
LM90-70, 7-6
I/O Table memory for S6 or S5 PLC, 5-9
I/O Terminal Blocks
introduction, 1-4
Input power requirements, 2-4
Input Range
Grouped Analog Input module, 5-45, 5-53, 5-61,
5-96
Inputs, 4-10
reading, 4-5
Intelligent modules, 4-6
L
LEDs, 2-2
Line Frequency
Grouped Analog Input module, 5-43, 5-51, 5-59
RTD module, 5-66
Thermocouple input module, 5-75
Load requirements, 2-6
Locations for I/O modules, 3-5
Logic power, 2-3
Logicmaster 90-70
monitoring I/O data, 7-6
software version required, 1-9
M
Micro Field Processor
backing up outputs, 4-17
backing up outputs from network, 4-18
configuring, 5-99
data defaults, 5-101
I/O references, 5-100
introduction, 1-3
operation with BIU, 4-14
reference parameters, 5-99
Module current requirements, 2-6
Module versions required for Hot Insertion, 2-7
Modules
BIU Terminal Block, 1-3
Bus Interface Unit, 1-3
I/O modules, 1-3
I/O Terminal Blocks, 1-4
Micro Field Processor, 1-3
types of, 1-2