Filter
Top Products
Detectors and Accessories | Seismic | 221
Certifications and Approvals
Region Certification
Europe CE 89/336/EEC, EN50130-4: 2002
(including A1 and A2), EN61000-6-3:
2001, EN61000-6-4: 2001
Germany VdS ISN-SM-50
ISN-SM-80
USA UL ANSR: Intrusion Detection Units (UL639)
the
Netherlands
NCP ISN-SM-50: 06229520/AA/00
X
Installation/Configuration Notes
Installation notes
Seismic detectors can be mounted directly onto steel plates
with smooth surfaces. The surface must not be painted and
must be level with a maximum deviation of 0.1 mm. If these
conditions cannot be met, the MXP0 mounting plate must
be used.
The seismic detector cannot be mounted directly onto
plastered or unplastered concrete.
Parts Included
Number Components
1 Seismic detector (ISN-SM-50 or ISN-SM-80)
1 Installation manual
1 Installation template
3 Cable ties
Technical Specifications
Electromagnetic sensitivity
Compatibility: Better than EN 50130-4
HF interference tol-
erance
(EN 61000-4-3):
No alarm or setup at critical frequencies within a range
of 1 MHz to 1000 MHz at > 30 V/m.
Housing
Dimensions: 8.9 cm x 8.9 cm x 2.2 cm
Weight: 0.320 kg
Environmental conditions
Humidity (EN60721): Up to 95% relative humidity, not condensing
Housing protection class
(EN 60529, EN 50102):
IP435
Temperature (operating): -40 °C to +70 °C
Temperature (storage): -50 °C to +70 °C
Function test
For the test: Low < 1.5 VDC
High > 3.5 VDC
Test duration (including test trans-
mitter ISN-GMX-S1):
≤ 3 sec
Operating radius according to monitoring area on concrete and steel for
all tools, including thermal tools
ISN-SM-50:
4 m radius = 50 m
2
monitoring area
ISN-SM-80:
5 m radius = 80 m
2
monitoring area
Outputs
Alarm relay (changeover contact): Contact closed in standby mode
(opened in the event of an alarm) de-
signed for 30 VDC, 100 mA, resist-
ance < 20 Ohm
Alarm holding time: Approx. 2.5 sec
Tamper switch/wall tamper: Tamper contact closed in standby
mode (opened in the event of tamper-
ing) designed for 30 VDC, 100 mA,
resistance < 45 Ohm
Test connection: Analog integration signal
Power requirements
Power consumption at
12 VDC:
Alarm: 6 mA
Standby: 3 mA
Power supply monitor-
ing:
8 VDC to 16 VDC (12 V nominal)
Alarm: < 7 VDC
Input for remote controlled reduction of sensitivity
For reduction: Low < 1.5 VDC
High > 3.5 VDC
Reduction to: 1/8 of current setting
Trademarks
SENSTEC
®
is a registered trademark of Siemens Building Technologies.
Ordering Information
ISN-SM-50 Seismic Detector
4 m operating radius on concrete and 50 m
2
monitoring area.
ISN-SM-50
ISN-SM-80 Seismic Detector
5 m operating radius on concrete and 80 m
2
monitoring area.
ISN-SM-80
Accessories
ISN-GMX-D7 anti-drill foil
For use with seismic detectors to provide drill
protection. Insert foil in the detector's cover to
provide extra tamper protection.
ISN-GMX-D7
ISN-GMA-S6 fixing device
For use with seismic detectors to monitor safes
and strong rooms. Consists of a detector plate,
a door plate, and a standby plate.
ISN-GMA-S6
ISN-GMX-B0 floor socket
For floor mounting a seismic detector. Weight:
2.08 kg. A surface at least 30 cm x 30 cm and
at least 80 cm deep is required.
ISN-GMX-B0
www.boschsecurity.com Bosch Security Systems B.V.
5