dhcp-bootp -- Configure the interface to use DHCP/Bootp server to acquire parameters. (p.
666)
■
■ ip-addr -- Interface IP address/mask. (IP-ADDR/mask-LENGTH) (p. 668)
■ svlan VLAN-ID ipv6 -- Configure various IP parameters for the VLAN (p. 668)
■ address -- Set IPv6 parameters for communication within an IP network (p. 664)
■ autoconfig -- Automatic address configuration. (p. 665)
■ dhcp -- Configure a DHCPv6 client. (p. 666)
■ full -- Obtain IPv6 address & Configuration information from DHCPv6 server. (p. 667)
■ rapid-commit -- Obtain IPv6 address quickly from DHCPv6 server. (p. 671)
■ ipv6-addr -- Configure a link-local IPv6 address. (IPV6-ADDR) (p. 668)
■ link-local -- Configure a link-local IPv6 address. (p. 669)
■ ipv6-addr/mask -- Configure IPv6 address represented in CIDR notation.
(IPV6-ADDR/PREFIX-LEN) (p. 668)
■ anycast -- Address that is assigned to a set of interfaces that typically belong to different
nodes (p. 665)
■ eui-64 -- An IPv6 EUI-64 address that can be automatically configured on any interface
(p. 667)
■ enable -- Enable IPv6 on an interface and configures an automatically generated link-local addr.
(p. 667)
■ [no] svlan VLAN-ID jumbo -- Labels this VLAN as a Jumbo VLAN, allowing you to pass packets
up to 9220 bytes in size (p. 669)
■ [no] svlan VLAN-ID monitor -- Define either the VLAN is to be monitored or not (p. 669)
■ all < In | Out | Both > -- Monitor all traffic. (p. 665)
■ mirror -- Mirror destination. (p. 669)
■ mirror_session_name -- Mirror destination name. (p. 669)
■ monitor_mirror_session_id < 1 to 4 > -- Mirror destination number. (p. 670)
■ svlan VLAN-ID name -- Set the VLAN's name (ASCII-STR) (p. 670)
■ svlan VLAN-ID protocol -- Set a predefined protocol for the current VLAN. (p. 670)
■ protocol-group -- Enter a list of protocols for the current VLAN delimited by commas.
(ASCII-STR) (p. 671)
■ protocols < IPX | IPv4 | IPv6 | ... > -- Set a predefined protocol for the current VLAN. (p. 671)
■ [no] svlan VLAN-ID qos -- Set VLAN-based priority (p. 671)
■ dscp -- Specify DSCP policy to use. (p. 666)
■ binary-range < 0 to 63 > -- Specify the DSCP code-point in binary. (BINARY) (p. 666)
■ integer-range < 0 to 63 > -- Specify the DSCP code-point in decimal. (p. 667)
■ well-defined < af11 | af12 | af13 | ... > -- Define mapping between a DSCP
(Differentiated-Services Codepoint) value and an 802 (p. 672)
■ priority < 0 | 1 | 2 | ... > -- Specify priority to use. (p. 670)
■ [no] svlan VLAN-ID tagged -- Assign ports to current VLAN as tagged ([ethernet] PORT-LIST) (p.
671)
■ [no] svlan VLAN-ID untagged -- Assign ports to current VLAN as untagged ([ethernet] PORT-LIST)
(p. 672)
■ [no] svlan VLAN-ID voice -- Labels this VLAN as a Voice VLAN, allowing you to separate, prioritize,
and authenticate voice traffic moving through your network (p. 672)
EXAMPLES
Example: svlan
Configure S-VLANS and ports connected to the customer network:
Edge1 (cong)# svlan100
Edge1(svlan-100)# untagged A1
Edge1(svlan-100)# exit
662© 2009 Hewlett-Packard Development Company, L.P.
svlanCommand Line Interface Reference Guide
