no-default -- Indicates that the router should never be used as a default by its
neighbors. (p. 255)
■
■ number < -2147483647 to 2147483647 > -- The router preferability number. Higher
values are more preferable. (p. 256)
■ local-proxy-arp -- Enable/disable local proxy ARP (p. 248)
■ mroute -- Configure IP Multicast Routing parameters on the VLAN interface (p. 254)
■ ttl-threshold < 0 to 255 > -- Set the multicast datagram TTL threshold for the interface
(p. 279)
■ ospf -- Enable/disable/configure Open Shortest Path First (OSPF) protocol on the VLAN
interface (p. 256)
■ all -- Process the request for all IP addresses. (p. 219)
■ area -- Specify an OSPF area. (p. 221)
■ area-id -- Single integer or IP address style dotted decimal. (OSPF-AREA-ID) (p.
222)
■ backbone -- The backbone area (the same as 0.0.0.0). (p. 226)
■ authentication -- Disable authentication. (p. 223)
■ authentication-key -- Set simple authentication method and key. (p. 223)
■ authentication-key -- OSPF authentication key (maximum 8 characters).
(OCTET-STR) (p. 223)
■ cost < 1 to 65535 > -- Set metric of this interface. (p. 229)
■ dead-interval < 1 to 65535 > -- Set dead interval in seconds; the default is 40. (p. 229)
■ hello-interval < 1 to 65535 > -- Set hello interval in seconds; the default is 10. (p. 236)
■ md5-auth-key-chain -- Set MD5 authentication method and key chain. (p. 250)
■ chain-name -- Specify key chain to use for MD5 authentication. (ASCII-STR) (p.
228)
■ passive -- Configures an ospf interface as passive. (p. 258)
■ priority < 0 to 255 > -- Set priority of this router as a designated router. (p. 265)
■ retransmit-interval < 1 to 3600 > -- Set retransmit interval in seconds; the default is
5. (p. 273)
■ transit-delay < 1 to 3600 > -- Set transit delay in seconds; the default is 1. (p. 279)
■ area -- Specify an OSPF area. (p. 221)
■ area-id -- Single integer or IP address style dotted decimal. (OSPF-AREA-ID) (p. 222)
■ backbone -- The backbone area (the same as 0.0.0.0). (p. 226)
■ authentication -- Disable authentication. (p. 223)
■ authentication-key -- Set simple authentication method and key. (p. 223)
■ authentication-key -- OSPF authentication key (maximum 8 characters). (OCTET-STR)
(p. 223)
■ cost < 1 to 65535 > -- Set metric of this interface. (p. 229)
■ dead-interval < 1 to 65535 > -- Set dead interval in seconds; the default is 40. (p. 229)
■ hello-interval < 1 to 65535 > -- Set hello interval in seconds; the default is 10. (p. 236)
■ ip-addr -- Specify the IP address the request is for. (IP-ADDR) (p. 241)
■ area -- Specify an OSPF area. (p. 221)
■ area-id -- Single integer or IP address style dotted decimal. (OSPF-AREA-ID) (p.
222)
■ backbone -- The backbone area (the same as 0.0.0.0). (p. 226)
■ authentication -- Disable authentication. (p. 223)
■ authentication-key -- Set simple authentication method and key. (p. 223)
■ authentication-key -- OSPF authentication key (maximum 8 characters).
(OCTET-STR) (p. 223)
■ cost < 1 to 65535 > -- Set metric of this interface. (p. 229)
■ dead-interval < 1 to 65535 > -- Set dead interval in seconds; the default is 40. (p. 229)
■ hello-interval < 1 to 65535 > -- Set hello interval in seconds; the default is 10. (p. 236)
■ md5-auth-key-chain -- Set MD5 authentication method and key chain. (p. 250)
209© 2009 Hewlett-Packard Development Company, L.P.
interfaceCommand Line Interface Reference Guide
