■ client-public-key -- Show currently loaded public keys for authorized clients (NUMBER) (p. 537)
■ babble -- Display phonetic hash. (p. 533)
■ fingerprint -- Display hexadecimal hash. (p. 552)
■ dns -- Show configured DNS server IP addresses on the switch (p. 549)
■ forward-protocol -- Show server addresses where broadcast requests received by the switch
are to be forwarded based on configured port (p. 552)
■ vlan -- Specify a vlan for which to show server addresses. (VLAN-ID) (p. 603)
■ helper-address -- Show DHCP servers where DHCP requests received by the switch are to be
forwarded (p. 555)
■ vlan -- Specify a vlan for which to show server addresses. (VLAN-ID) (p. 603)
■ host-public-key -- Display the SSH host RSA public key (NUMBER) (p. 555)
■ babble -- Display phonetic hash. (p. 533)
■ fingerprint -- Display hexadecimal hash. (p. 552)
■ icmp -- Show ICMP Rate Limiting settings (p. 556)
■ igmp -- Invoked without any parameters, shows per-VLAN IGMP status, or, if VLANs are disabled
displays the global IGMP status (p. 556)
■ config -- Show IGMP configuration information. (p. 540)
■ group -- Show ports the specified multicast group address is registered on. (IP-ADDR) (p.
553)
■ vlan -- Show IGMP operational information for the VLAN specified. (VLAN-ID) (p. 603)
■ config -- Show IGMP configuration information for the VLAN specified. (p. 540)
■ irdp -- Show IRDP (ICMP Router Discovery Protocol) settings (p. 563)
■ mroute -- Show IP multicast routing table (p. 571)
■ interface -- Show IP multicast routing interfaces' information (p. 559)
■ VLAN-ID -- Specify the VLAN ID of the IP multicast routing interface to show. (VLAN-ID)
(p. 607)
■ IP-ADDR -- Show detailed information for the specified entry from the IP multicast routing
table (IP-ADDR) (p. 562)
■ IP-ADDR -- Specify the source IP address of the MRT entry. (IP-ADDR) (p. 562)
■ ospf -- Show OSPF operational and configuration information (p. 574)
■ area -- Show OSPF areas configured on the device (p. 529)
■ area-ip -- (OSPF-AREA-ID) (p. 530)
■ external-link-state -- Show the Link State Advertisements from throughout the areas to
which the device is attached (p. 550)
■ advertise -- Show each LSA as a stream of bytes in hexadecimal notation. (p. 529)
■ link-state-id -- Show LSAs with the specified ID only. (IP-ADDR) (p. 566)
■ router-id -- Show LSAs with the specified Router ID only. (IP-ADDR) (p. 587)
■ sequence-number -- Show LSAs with the specified sequence number only. (p. 589)
■ status -- The keyword is optional and can be omitted. (p. 596)
■ general -- Show OSPF basic configuration and operational information (p. 553)
■ interface -- Show OSPF interfaces' information (p. 559)
■ if-ip -- Specify IP address of the interface for which to show detailed information.
(IP-ADDR) (p. 556)
■ vlan -- Specify VLAN of the interface for which to show detailed information. (VLAN-ID)
(p. 603)
■ link-state -- Show all Link State Advertisements from throughout the areas to which the
device is attached (p. 565)
■ advertise -- Show each LSA as a stream of bytes in hexadecimal notation. (p. 529)
■ area-id -- Show LSAs for the specified area only. (OSPF-AREA-ID) (p. 530)
■ link-state-id -- Show LSAs with the specified ID only. (IP-ADDR) (p. 566)
■ router-id -- Show LSAs with the specified Router ID only. (IP-ADDR) (p. 587)
■ sequence-number -- Show LSAs with the specified sequence number only. (p. 589)
■ status -- The keyword is optional and can be omitted. (p. 596)
514© 2009 Hewlett-Packard Development Company, L.P.
showCommand Line Interface Reference Guide
