DMP Electronics XR500 Home Security System User Manual


  Open as PDF
of 84
 
XR500 Series Canadian Programming Guide Digital Monitoring Products
1
inTroduCTion
Introduction
1.1 Before you Begin
This guide provides programming information for the DMP XR500, XR500N, and XR500E Command
Processor™ Panel. After this Introduction, the remaining sections describe the functions of each
programming menu item along with the available options. Before starting to program, we recommend
that you read through the contents of this guide. The information contained here allows you to quickly
learn the programming options and operational capabilities of the XR500, XR500N, and XR500E panels.
In addition to this guide, you should also read and be familiar with the following XR500 Series Canadian
documents:
• XR500SeriesCanadianInstallationGuide(LT-0681CAN)
• XR500SeriesCanadianProgrammingSheet(LT-0678CAN)
• XR100/XR500CanadianSecurityCommand
®
User’sGuide(LT-0683CAN)
Internal Programmer
Thepanelcontainsallofitsprogramminginformationinanon-boardprocessoranddoesnotrequirean
externalprogrammer.Youcanperformallprogrammingtasksthrougha32-characterDMPalphanumeric
keypad set to address one.
Programming Information Sheet
Included with each panel are the Programming Information Sheets. These list the various programming
prompts and available options for programming the panel. Before starting to program, we recommend you
completelyllouteachsheetwiththeprogrammingoptionsyouintendtoenterintothepanel.
Having completed programming sheets available before entering data helps prevent errors and can shorten
the time you spend programming. Completed sheets also provide you with an accurate panel program
recordyoucankeeponleforfuturesystemserviceorexpansion.TheremainderofthisIntroduction
provides instructions for starting and ending a programming session using the alphanumeric keypad.
1.2 Getting Started
Ground Yourself Before Handling the Panel! Touch any grounded metal, such as the enclosure, before
touching the panel to discharge static.
Remove All Power From the Panel! Remove all AC and Battery power from the panel before installing or
connecting any modules, cards, or wires to the panel.
Before starting to program the XR500 Series Canadian panel, make sure the panel is properly grounded and
AC and battery power is applied to the appropriate panel terminals. All wiring connections and grounding
instructionsaredetailedintheXR500SeriesCanadianInstallationGuide(LT-0681).
(LT-0759).
Accessing the Programmer
1.InstalltheresetjumperacrossthetwoJ16
reset pins for two seconds.
2. Remove the reset jumper and place it over just
one pin for future use.
3.Enterthecode6653(PROG)intoa
32-characteralphanumerickeypadset
to address one, supervised mode. Press
COMMAND.
4.ThekeypaddisplaysPROGRAMMER.
You are now ready to start programming the panel.
J6
Interface
Card
Expansion
Connector
Momentarily place the Reset
jumper over both of the J16
pins to reset the panel.
AC
12345678 10 11 12 13 14 15 16 17 18 199202122232425262728
+B BELLGND SMK GNDREDYEL GRNBLK Z1 Z2 Z3 Z4 Z5 Z6 Z7 Z8 Z9+Z9–Z10+Z10–AC –B GND GND GNDGND
K6 K7
Output 1Output 2
J3
Phone Line
J10
J22
LX-Bus
Battery
Start
J23
J21
RS-232
Power
LED
J8
PROG
J4
Tamper
J16
Reset
Out1 Out2
Outputs 3-6
J11
3
4
5
6
J2
J1
Ethernet
R
L
X
OVC
Link LED
Activity LED
Figure 1: XR500 Series Canadian Panel Showing Reset
 previous next