Mitsubishi Electronics FX3UC Garage Door Opener User Manual


 
610
FX3S/FX3G/FX3GC/FX3U/FX3UC Series
Programming Manual - Basic & Applied Instruction Edition
25 Block Data Operation – FNC190 to FNC199
25.3 FNC194~199 – BKCMP=, >, <, < >, <=, >= / Block Data Compare
Caution
When using 32-bit counters (including 32-bit high-speed counters)
For comparing 32-bit counters and 32-bit high-speed counters (C200 to C255), make sure to use an instruction for
32-bit operation (DBKCMP=, DBKCMP>, DBKCMP<, DBKCMP<>, DBKCMP<=, or DBKCMP>=).
If an instruction for 16-bit operation (BKCMP=, BKCMP>, BKCMP<, BKCMP<>, BKCMP<=, or BKCMP>=) is used,
an operation error is caused (error code: K6705).
Note that the 32-bit value [n+1, n] is valid when D or R is specified as "n" in a 32-bit instruction.
In the case of "DBKCMP = D0 D100 M0 R0", "n" is [R1, R0].
Errors
An operation error is caused in the following cases; The error flag M8067 turns ON, and the error code is stored in
D8067.
When the range of "n" ("2n" in 32-bit operation) points starting from and/or exceeds the
corresponding device range (error code: K6706)
When the range of "n" points starting from exceeds the corresponding device range (error code: K6706)
When data registers starting from specified as "D.b" overlap "n" ("2n" in 32-bit operation) points starting
from (error code: K6706)
When data registers starting from specified as "D.b" overlap "n" ("2n" in 32-bit operation) points starting
from (error code: K6706)
When a 32-bit counter (C200 to C255) is specified in and/or in 16-bit operation (error code: K6705)
For comparing 32-bit counters, make sure to use an instruction for 32-bit operation (DBKCMP=, DBKCMP>,
DBKCMP<, DBKCMP<>, DBKCMP<=, or DBKCMP>=).
Program example
1) In the program shown below, four 16-bit binary data starting from D100 are compared with four 16-bit binary data
starting from D200 by BKCMP= (FNC194) instruction when X020 is set to ON, and the comparison result is stored
in four points starting from M10.
When the comparison result is "ON (1)" in all of the four points starting from M10, Y000 is set to ON.
2) In the program shown below, the constant K1000 is compared with four data starting from D10 when X010 is set
to ON, and the comparison result is stored in b4 to b7 of D0.
S
1
S
2
D
D
S
1
D
S
2
S
1
S
2
D100
Comparison
result
=
K1000
K2000
K4000
K3000
D101
D102
D103
OFFY000
D200
K1000
K2000
K4000
K5000
D201
D202
D203
M10
ON
ON
ON
OFF
M11
M12
M13
X020
FNC194
BKCMP=
D100 D200 M10
END
K4
Y000
M8090
Block comparison signal
(When all of M10 to M13 are ON, Y000 is set to ON.)
<>K1000
K2000
K1000
K2222
K1000
X010
FNC197
BKCMP<>
K1000 D10 D0.4
END
K4
D10
D11
D12
D13
b15
b7 b4 b0
D0 before
operation
0000010001000010
b15 b7 b4 b0
D0 after
operation
0000100101000010