Filter
Top Products
03_NVspec_ver304e
3-3.Configuration Properties
Description
nc
No.
Name Valid Range Unit, Default Page.
nciMinOutTm
SNVT_time_sec
nciStartHrtBt
SNVT_time_sec
nciStartOutTm
SNVT_time_sec
nciInitStartTm
SNVT_time_sec
nciInitOutTm_1
SNVT_time_sec
nciInitOutTm_2
SNVT_time_sec
nciSndHrtBt_1
SNVT_time_sec
nciSndHrtBt_2
SNVT_time_sec
nciAnalogWidth
SNVT_temp_p
nciAnlgMonTm
SNVT_time_sec
nciRcvHrtBt_1
SNVT_time_sec
nciRcvHrtBt_2
SNVT_time_sec
nciEffectTm_1
SNVT_time_sec
nciEffectTm_2
SNVT_time_sec
nciPollFetch
SNVT_switch
nciOffline
SNVT_switch
nciCoolLrSetP
SNVT_temp_p
nciHeatUpSetP
SNVT_temp_p
nciRmOpLck
SNVT_switch
nciRmDsp_1
SNVT_switch
nciRmDsp_2
SNVT_switch
nciSet_1
SNVT_switch
0(display) 4721 nc38
Set the validity of the intake temperature display for the local remote
controller.
48
46
46
46
47
43
43
44
45
41
41
42
42
39
39
40
40
36
37
37
38
Item
1 nc15 6553.5 seconds (invalid)
6553.5 seconds (As 1800 seconds)2 nc16
1.0 to 600.0 seconds 1sec
1200.0 to 6540.0 seconds 60sec
Minimum Send Time
Send Heartbeat Start Time
Set the minimum transmission interval between output network variables.
3 nc17 6553.5 seconds (As 1800 seconds)1200.0 to 6540.0 seconds 60secSend Start Time
6553.5 seconds(invalid)
5 nc19 6553.5 seconds (invalid)
4 nc18 0.0 second、1200.0 to 3600.0 seconds 60secInitialize Start Time
Initialize Send Time_1
6553.5 seconds (invalid)
6 nc20 6553.5 seconds (invalid)0.0 second、5.0 to 50.0 seconds 1.0sec
7 nc21
Initialize Send Time_2
Send Heartbeat_1
8
nc24
nc22 6553.5 seconds (invalid)
0.5 to 2.0℃ 0.5℃
SW1-3 is OFF：0.0 second、600.0～6540.0 seconds
SW1-3 is ON：0.0 second、60.0 to 6540.0 seconds
10sec
9
Send Heartbeat_2
6553.5 seconds (As 600.0 seconds)
-0.01℃(As 1.0℃)
0.0 second (As 1800.0 seconds)
10 nc25
11
SW1-3 is OFF：0.0 second、600.0 to 6540.0
seconds
10sec
600.0 to 6540.0 seconds 60sec
14
0.0 second (As 1800.0 seconds)nc27
nc26
13 nc28
12
6553.5 seconds (As 600.0 seconds)
6553.5 seconds (As 600.0 seconds)
nc29
600.0 to 6540.0 seconds 60sec
60.0 to 6540.0 seconds
0(disable) *Always effective
0(disable) *Always effectivenc31
nc30
State=0(disable)、1(enable) --
State=0(Response)、1(non-response) --15
16
18 nc35
17 nc34Lower Setpoint Cooling
Upper Setpoint Heating
Set the heat upper limit temperature setting value for the local remote
controller.
0(display)
0(All button)
- 0.01℃(As 28℃)
- 0.01℃(As 19℃)
22 nc39
19
20
Local Operation Lock
Local Display_1
Local Display_2
Communication Timing
Set the simple lock setting value for the local remote controller.
Set the validity of the automatic actual operation mode display for the local
remote controller.
0(initialize)
nc37
nc36
0.0 second、0.1 to 1.0 seconds 0.1sec
0.0 second、600.0 to 6540.0 seconds 60sec
60sec
60.0 to 600.0 seconds 60sec
19.0℃ to 30.0℃ 1.0℃
17.0℃ to 28.0℃ 1.0℃
State=0(initialize)、1(setting time) --
State=0(All button）、1（except Start/Stop button) --
State=0(display)、1(no display) --
State=0(display)、1(no display) --
Spacetemp Width
Monitoring Time
Receive Heartbeat_1
Receive Heartbeat_2
Effective Time_1
Effective Time_2
Effective PollFetch
Effective Offline Mode
Set the start time of network variable change at power ON.
Set the automatic update start time at power ON.
Set the start time of initial output change at power ON.
Set the minimum transmission interval between output network variables
at initial output.
Set the minimum transmission interval between each unit during initial
output.
Set the output network variable's update interval.
Set the output network variable's update interval.
Set the minimum fluctuation width of the output when the indoor
temperature state output changes.
Set the set time monitor interval of the indoor temperature for the indoor
unit.
Set the maximum elapse time from the previous update.
Set the maximum elapse time from the previous update.
Set the effective time for the emergency stop command.
Set the networks communication start timing.
Set the effective time for the collective operation prohibit command.
Set the presence of a response for poll (Fetch) requests in respect to the
output network variables.
Set the validity of the offline mode at power ON.
Set the cool/dry lower limit temperature setting value for the local remote
controller.
WSN02-2124 - 12 -