Filter
Top Products
Batch Feed Granulators CHS-810, CHS-814, CHS-819 and CHS-824
OPTIONAL OPEN ROTOR
with scissor-cutting, slant knives
STANDARD STAGGERED ROTOR
with disposable, cassette knives
2-2 l Technical Specifications
MODELS CHS-810 CHS-814 CHS-819 CHS-824
Performance characteristics
Throughput* lb/hr {kg/hr} 200 {90} 250 {115} 330 {150} 400 {180}
Cutter chamber opening in. {mm} 8.7 x 9.5 8.7 x 14.2 8.7 x 18.9 8.7 x 23.6
{220 x 240} {220 x 360} {220 x 480} {220 x 600}
Rotor speed rpm 356 356 356 356
Cutting Circle in. {mm} 7.88 {200} 7.88 {200} 7.88 {200} 7.88 {200}
Standard motor power Hp 5 7.5 10 10
Drive type belt drive
Hopper type hand, robot, conveyor - standard (sheet, roll, profile, side feed - optional)
Vacuum discharge side rear
Screen mesh sizes
5
/32,
3
/16,
1
/4,
5
/16,
3
/8,
1
/2
in. {4, 5, 6, 8, 10, 12 mm}
Rotor type staggered rotor - open rotor optional (except for CHS-824)
Knives
Number of rotating knives 3 X 2 3 X 3 3 X 4 3 X 5
Number of bed knives 2 2 2 2
Dimensions inches {mm}
A - Height - hopper closed 57 {1450} 57 {1450} 57 {1450} 57 {1450}
B - Height - hopper open 72 {1830} 72 {1830} 72 {1830} 72 {1830}
C - Width 26.75 {680} 31.50 {800} 36.25 {920} 41 {1040}
D - Base depth 35.5 {900} 35.5 {900} 35.5 {900} 35.5 {900}
E - Overall depth 54.75 {1390} 54.75 {1390} 54.75 {1390} 54.75 {1390}
F - Infeed height 45 {1145} 45 {1145} 45 {1145} 45 {1145}
G - Feed hopper opening - width 9.44 {240} 14.13 {360} 18.86 {480} 23.63 {600}
H - Feed hopper opening - height 10.25 {200} 10.25 {200} 10.25 {200} 10.25 {200}
Weight lb {kg}
Installed 750 {340} 794 {360} 1014 {460} 1279 {580}
Shipping 882 {400} 926 {420} 1169 {530} 1477 {670}
Voltages Total amps based on standard motor
208V/3 phase/60 Hz 20 24 31 31
230V/3 phase/60 Hz 18 22 28 28
460V/3 phase/60 Hz 9 11 14 14
575V/3 phase/60 Hz 7 9 11 11
Noise level
†
With integral soundproofing 80-85 dbA
SPECIFICATION NOTES:
* Throughput is based on a
3
/8 inch {
9.53 mm}
screen.Throughput rates are provided as a capacity guideline only.
Throughput will vary according to size, shape, thickness and properties of the material to be cut, as well as the
desired size of the granulate. Consult Conair for a material test or help determining the correct granulator model for
your application.
† Noise level will vary according to material type being processed and the granulator configuration.These ranges are
based on tests using SPI standards.
Specifications may change without notice. Check with a Conair representative for the most current information.
OPTIONS
MOTOR OPTIONS ●=standard o=optional
CHS-810 CHS-814 CHS-819 CHS-824
5 Hp ● N/A N/A N/A
7.5 Hp o ● oo
10 Hp o o ●●
15 Hp o o o o
• Discharge: manual, vacuum
(standard), blower
• Hardened cutter housing
• Third bed knife
• 3-blade open rotor
• High RPM (512 RPM) motor
H
G
C
D
A
B
E
F
TPGS019/0603