Filter
Top Products
– 147 –
6. Set error
If flashing
ERROR
is displayed when the program operation has been set up, correct the
time following the procedure below.
1. When flashing
ERROR
is displayed, ON time of the failed program flashes.
2. Push
SET
button to flash the time to be corrected.
3. Using
HH
/
MM
buttons, correct ON/OFF time.
4. Push
SET
button. When the setup is correctly performed,
ERROR
display disappears.
5. The correction has completed by pushing
PROGRAM
button.
CAUTION
• When ON/OFF time is set as follows,
ERROR
is displayed.
1) When a part of the operation time makes inroads into a part of another operation time
ERROR
SuMoTuWeThFrSa
PROGRAM1
PROGRAM2
PROGRAM3
Example: ON time OFF time
2) When OFF time is ahead of ON time
Example: ON time OFF time
3) When ON time is same as OFF time
Example: ON time OFF time
4) ON time or OFF time is singly set up
Example: ON time OFF time
[Is not set]
• The following cases are not set error.
1) OFF time of the previous cycle is same as ON time of the next cycle.
Example: ON time OFF time
2) When the next cycle is set to the time before the
set time of the previous cycle
Example:
ON time OFF time
ON time OFF time
Pushing the
PROGRAM
button changes the order in order of time.
3) When both ON and OFF times are same
Example: ON time OFF time
0:00 23:59
ON OFF
ON OFF
0:00 23:59
OFF ON
0:00 23:59
ON OFF
0:00 23:59
ON OFF
0:00 23:59
ON OFF
ON OFF
0:00 23:59
ON OFF
ON OFF
Continuous operation
for 24 hours
7. How to copy the program operation time
When setting the program operation, already set program can be copied and set to
the other day of the week.
<Example: To copy the operation contents of Monday to Tuesday>
1. Push
CHECK
button in normal display.
2. Push
DAY
button and put the operation reserve
indication
on the day of the week of which the
program operation is already set.
(Monday in the example)
3. Push
PROGRAM
button.
Present day of the week indication
and Operation
reserve indication
flash.
4. Push
DAY
button and put the present day of the
week indication
on the day of the week to be copied.
(Tuesday in the example) (For continuous copying,
push
SET
button, and then push
DAY
button.)
1
Push
CHECK
button.
<Example: Case to check the program
operation time of Wednesday in Monday>
• The operation reserve indication
flashes in
the normal display status.
CAUTION
1. While reserve indication is
flashing, the display does not
change even if other buttons are
pushed than
DAY
,
CHECK
, and
PROGRAM
button.
2. If 30 seconds have passed while
the reserve indication
is flashing
without pushing
DAY
,
CHECK
or
PROGRAM
button, the display returns
automatically to the original
display. (Normal display)
5. Push
PROGRAM
button. The operation reserve indication goes on under the copied day of
the week.
8. How to check the program operation time
2
Push
DAY
button and put the operation
reserve indication
on the day of the week
to be checked.
• Every pushing
DAY
button, the operation
reserve indication
flashes and the contents
of program operation time of the day of the
week on which the operation reserve
indication
has been put on is displayed.
WEEKLY TIMER
ERROR
SuMoTuWeThFrSa
PROGRAM1
PROGRAM2
PROGRAM3
CHECK
PROGRAM
SET
DAY
HH MM
CLEAR
CANCEL
WEEKLY TIMER
ERROR
SuMoTuWeThFrSa
PROGRAM1
PROGRAM2
PROGRAM3
CHECK
PROGRAM
SET
DAY
HH MM
CLEAR
CANCEL
1,
3
2
3
Push
CHECK
button.
• It turns to be normal indication.
ERROR
SuMoTuWeThFrSa
PROGRAM1
PROGRAM2
PROGRAM3
ERROR
SuMoTuWeThFrSa
PROGRAM1
PROGRAM2
PROGRAM3
RBC-EXW21E