Filter
Top Products
X GEM-P3200 Programming Instructions
L NAPCO Security Systems
Page 50
WI818G 10/05
EXTERNAL RELAY CONTROL
STEP 4: EVENT ID CODES: Each relay event can be assigned any of the available event IDs from the table.
Select 2-digit Event ID from Table 4 (below); enter in corresponding address locations (left and right digit).
Continued
TABLE 4
EVENT ID CODES
DATA ENTRIES OPTION
LEFT RIGHT
blank (•) blank (•) Area 1 Arm
blank (•) 1 Area 2 Arm
blank (•) 8
Zone 1
blank (•) 9
Zone 2
blank (•) 0
Zone 3
blank (•) B
Zone 4
blank (•) C
Zone 5
blank (•) D
Zone 6
blank (•) E
Zone 7
blank (•) F
Zone 8
1 blank (•)
Zone 9
1 1
Zone 10
1 2
Zone 11
1 3
Zone 12
1 4
Zone 13
1 5
Zone 14
1 6
Zone 15
1 7
Zone 16
1 8
Zone 17
1 9
Zone 18
1 0
Zone 19
1 B
Zone 20
1 C
Zone 21
1 D
Zone 22
1 E
Zone 23
1 F
Zone 24
2 blank (•)
Zone 25
2 1
Zone 26
2 2
Zone 27
2 3
Zone 28
2 4
Zone 29
2 5
Zone 30
2 6
Zone 31
2 7
Zone 32
2 8
Zone 33
2 9
Zone 34
2 0
Zone 35
2 B
Zone 36
2 C
Zone 37
2 D
Zone 38
2 E
Zone 39
2 F
Zone 40
3 blank (•)
Zone 41
3 1
Zone 42
3 2
Zone 43
3 3
Zone 44
3 4
Zone 45
3 5
Zone 46
3 6
Zone 47
3 7
Zone 48
C blank (•) Area 1 disarm
C 1 Area 2 disarm
6 8
Area 1 Keypad Ambush
6 9
Area 1 Keypad Panic
6 0
Area 1 Keypad Fire
6 B
Area 1 Keypad Medical
6 C
Keypad Tamper
6 D
Area 1 Fail to Open
6 E
Area 1 Fail to Close
7 blank (•)
Area 2 Keypad Ambush
7 1
Area 2 Keypad Panic
7 2
Area 2 Keypad Fire
7 3
Area 2 Keypad Medical
7 5
Area 2 Fail to Open
7 6
Area 2 Fail to Close
0 8
Test Timer
0 0
Bus Fail
0 B
Guarded RAM Fail
0 C
Low Battery
0 D
AC Fail
0 E
EZM Tamper
0 F
Sensor Watch
B blank (•)
Telco Fault
B 8
Digital Dialer Test
B 9
RESERVED
B B
Service Message
B C
Program Change
B D
RF Receiver Trouble
B E
Transmitter Tamper
B F
Transmitter Trouble
D blank (•)
Keypad Fail
D 1
EZM Fail
D 2
Quickloader Device Control
D 3
System Shutdown
D 4
Quickloader Keypad Reset
D 5
General System Alarm
D 8
Area 1 General System Alarm
D 9
Area 2 General System Alarm
F blank (•)
Relay Group 1
F 1
Relay Group 2
F 8
Area 1 Entry Delay
F 9
Area 2 Entry Delay
NOTE: Keypad Tamper must be enabled in
UL installations using jumper op-
tion on keypad.