Filter
Top Products
L NAPCO Security Systems
X GEM-P3200 Programming Instructions
Page 21
WI818G 10/05
ADDRESS 0525
CS Receiver 1
Format
ADDRESS 0550
CS Receiver 2
Format
Default for CS Receiver 1 Format depends on Easy Menu Question “RCVR FORMAT”. [Default = •(blank) E] for CS Receivers 1, 2 and 3 Formats.
CS RECEIVER FORMAT OPTIONS (ADDRESS 0520, 0521, 0525, 0526, 0550, 0551, 0575 & 0576)
CS RECEIVER FORMATS: Up to 3 CS Formats may be programmed.
1. Select the desired CS Receiver Format from the table shown.
2. Enter in the corresponding digit address locations for each CS
Receiver.
NOTE: Dark shaded data value box shows option not available.
Default for CS Receiver 1 Format depends on Easy Menu Question “RCVR
FORMAT”. [Default = •(blank) E] for CS Receivers 2 and 3 Formats.
CS RECEIVER FORMATS: Up to 3 CS Formats may be pro-
grammed.
1. Select the desired CS Receiver Format from the table shown.
2. Enter the corresponding digit in the address location for each CS
Receiver.
NOTE: Dark shaded data value box shows option not
available. Press [Enter] of [ON/OFF] to save.
NOTES:
* If both are selected, 1400Hz has priority over 2300Hz.
** For NAPCO NetLink™ installations only: For each telephone num-
ber desired, enable to allow the panel to report alarms via the NL-MOD
accessory. See WI1242 for more information.
LEADING DIGITS FOR PAGER FORMAT: In Pager Format reporting, the message typically begins with “00”. However, for some
pager services, this will cause the Pager's Voice Mail feature to activate. This option allows you to program these digits to any
number desired. Typical Pager report is “003 022 1234”, where 3 is the Event, 22 is the zone, and 1234 is the Subscriber ID
number. For example, if the Leading Digits are programmed as “98”, the Pager report will now appear as “983 022 1234”.
1. Enter in 1st and 2nd Leading Digits in right digit only (left digit is not used) as shown.
2. Valid entries are: 0-9. Press U or D to save
CS RECEIVER FORMAT OPTIONS
ADDRESS 0575
CS Receiver 3
Format
ADDRESS 0520
Leading Digits
for Pager
Format
(1st Digit)
[Default = blank (•) blank (•)]
ADDRESS 0521
Leading Digits
for Pager
Format
(2nd Digit)
[Default = blank (•) blank (•)]
0526
CS Receiver 1 Options
0551
Default
Option
Default
Option
OFF
1
1400Hz Handshake/Kissoff *
OFF
1
1400Hz Handshake/Kissoff *
OFF
2
2300Hz Handshake/Kissoff *
OFF
2
2300Hz Handshake/Kissoff *
OFF
3
Enable Zone Number on Pulse Alarm
OFF
3
Enable Zone Number on Pulse Alarm
OFF
4
Single Digit Only
OFF
4
Single Digit Only
OFF
5
Sum Check OFF
5
Sum Check
OFF
6
3/1 with Extended Restores OFF
6
3/1 with Extended Restores
OFF
7
Report to TCP/IP Receiver or AES (Telco 1)** OFF
7
Report to TCP/IP Receiver or AES (Telco 2)**
OFF
8
RESERVED OFF
8
RESERVED
CS Receiver 2 Options
0576
Default
Option
OFF
1
1400Hz Handshake/Kissoff *
OFF
2
2300Hz Handshake/Kissoff *
OFF
3
Enable Zone Number on Pulse Alarm
OFF
4
Single Digit Only
OFF
5
Sum Check
OFF
6
3/1 with Extended Restores
OFF
7
Report to TCP/IP Receiver or AES (Telco 3)**
OFF
8
RESERVED
CS Receiver 3 Options
DATA ENTRIES
LEFT RIGHT
blank (•) blank (•)
Ademco Slow, Silent Knight Slow
blank (•)
1
Sescoa, Vertex, DCI, Franklin Fast
blank (•)
2
Radionics Fast
blank (•)
3
Silent Knight Fast
blank (•)
4
Radionics, DCI, Franklin Slow
blank (•)
5
Universal High Speed
blank (•)
8
Radionics BFSK
blank (•)
9
FBI 4/3/1
blank (•)
0
Radionics Modem 2
blank (•)
B
SIA
blank (•)
C
Ademco Point ID
blank (•)
D
Ademco Express
blank (•)
E
Pager
1 blank (•)
Radionics Modem IIe
CS RECEIVER FORMATS
blank (•)
F
Disabled