Filter
Top Products
ICP-CC488 | Installation Guide | 8.0 Alarm Link Software EN | 40
Bosch Security Systems, Inc. | 12/08 | F01U089457-02
If you are required to disable the ability restore the
control panel to its default settings, a special
procedure eliminates the possibility of accidentally
setting this option. You must hold down the default
button on the printed circuit board (PCB) when
programming this location.
To prevent manually restoring the default
control panel settings:
1. Enter the Installer Code (the default is 1234) and
press [#] to enter Installer’s Programming Mode.
Two beeps sound and the remote codepad
displays the data programmed in Location 000.
If you are using the remote codepad, the STAY
and AWAY indicators flash to indicate you
entered Installer’s Programming Mode.
2. Enter [9 0 0 #] to move to Location 900.
3. Press and hold the default button.
The default button is located at the top of the
PCB next to the PROGRAMMING KEY socket.
4. Enter [1 5 *] to program 15 into Location 900.
5. Release the default button.
6. Enter [9 6 0 #] to exit from Installer’s
Programming Mode.
Two beeps sound and the system returns to the
disarmed state.
If you are using a remote codepad, the STAY
and AWAY indicators are extinguished to
indicate that the system is disarmed.
If Location 900 is not programmed as 15, do one of
the following procedures to restore the default
control panel settings.
To default the control panel settings using the
Installer Code:
1. Enter the Installer Code (the default is 1234) and
press [#] to enter Installer’s Programming Mode.
Two beeps sound. The STAY and AWAY
indicators flash to indicate you entered Installer’s
Programming Mode.
2. Enter [9 6 1 #].
Two beeps sound after the default control panel
settings are restored.
3. Enter [9 6 0 #].
Two beeps sound. The STAY and AWAY
indicators stop flashing and the system returns to
the disarmed state.
The control panel default factory settings are
restored.
To restore the default control panel settings using
the default button:
1. Disconnect the AC MAINS supply and the
backup battery from the control panel.
2. Press and hold the default button.
The default button is located at the top of the
PCB next to the PROGRAMMING KEY socket.
3. Reconnect the AC MAINS supply to the control
panel.
4. Wait 3 to 5 sec and release the default button.
5. Enter [2 5 8 0 *] to disarm the system using the
default Master Code.
The control panel default factory settings are
restored.
If the option to restore the default control
panel settings is disabled using Location
900:
• The dialer seize relay (RL2) clicks
four times. You must return the
control panel to Bosch Security
Systems, Inc. for exchange. If the
Installer Code is unknown, a service
fee is charged to unlock the control
panel’s memory
• When programmed to disable the
default control panel setting, you
cannot use the command [961#] to
retrieve the programming data.
• The use of this feature is not
recommended.
8.0 Alarm Link Software
You can program or control the ICP-CC488 Control
Panel remotely using an IBM or compatible personal
computer and the CC816 Alarm Link Software. This
software allows you to change your customer’s
control panel without leaving your office, which
improves customer service and saves you time and
money. For locations where a control panel is
installed hundreds of kilometers from your office, the
Upload/Download feature is invaluable.
When selecting the control panel type during the
setup of a new customer database in the Alarm Link
Software, the software version number is
ICP-CC488
V1.0X and the panel type is I488.
When you add a new customer in the Alarm Link
Software, the Subscriber ID Number and the Installer
Code must match the values programmed in the
control panel for synchronization during connection
to the control panel. If these two locations do not
match those of the control panel, the computer and
the control panel cannot be synchronized.
8.1 Remote Connect
The remote connect feature allows you to establish a
connection through the telephone network from your
IBM or compatible computer to the ICP-CC488
Control Panel. This software allows you to offer
faster service to your clients.
8.1.1 Remote Connection with Customer
Control
If you want to configure the control panel so that a
remote connection can be established only when the
client initiates it through the remote codepad,
program the following information: