Filter
Top Products
ICP-CC488 | Installation Guide | 5.0 System Functions EN | 30
Bosch Security Systems, Inc. | 12/08 | F01U089457-02
4. Press [STAY][2][AWAY].
Two beeps sound and the system returns to the
disarmed state.
Example
If you want to automatically divert all unanswered
incoming calls to another telephone number (for
example, 9672 1777) when the system is armed in
AWAY Mode, enter:
[2 5 8 0 3][AWAY][1][AWAY][STAY]
[1 6 1 9 6 7 2 1 7 7 7][STAY][2][AWAY]
You can suspend the telco arming sequence at any
time. To disable the telco arming sequence:
Enter your Master Code and press [3][AWAY][1]
[AWAY][STAY][4][AWAY].
To program the telco disarming sequence:
1. Enter your Master Code and press [3][AWAY].
Three beeps sound and the STAY and AWAY
indicators flash.
2. Press [2][AWAY] to change the telco disarming
sequence.
Three beeps sound.
If a telco disarming sequence is already
programmed, the sequence is displayed one digit
at a time using the remote codepad indicators.
Refer to Table 30 on page 29 for the indicators
and their meanings.
If no telco disarming sequence is programmed,
an additional two beeps sound after entering this
mode. These two beeps normally sound after the
last digit of the sequence is displayed.
3. Enter the desired call forward disable sequence.
For example, program [# 6 1 #] to disable the
call forward – no answer sequence, or [# 2 1 #]
to disable the call forward – immediate sequence.
\
When you program a # in the telco arm
sequence, enter [STAY][2].
4. Press [AWAY].
Two beeps sound and the system returns to the
disarmed state.
You can suspend the telco disarming sequence at any
time. To disable the telco disarming sequence:
Enter your Master Code and press [3][AWAY][2]
[AWAY][STAY][4][AWAY].
5.2.6 Setting STAY Mode 2 Zones
This function allows the Master Code holder to select
the zones that are isolated automatically when the
system is armed in STAY Mode 2.
To arm the system in STAY Mode 2, press and hold
[0] until two beeps sound. Refer to Section 5.4.3 or
Section 3.5 Arming The System in STAY Mode 2 for more
information.
To set STAY Mode 2 zones:
1. Enter your Master Code and press [4][AWAY].
Three beeps sound and the STAY indicator
flashes.
2. Enter the number of the zone you want to
automatically isolate and press [STAY].
The corresponding zone indicator flashes.
3. Repeat Step 2 to select each zone.
As each zone is selected to be isolated,
the corresponding zone indicator flashes.
If you make a mistake, enter the incorrect
zone number and press [STAY]. This zone
is no longer selected to be isolated and
the zone indicator is extinguished.
This function does not work on a
partitioned ICP-CC488 Control Panel.
4. Press [AWAY].
Two beeps sound and the system returns to the
disarmed state.
The indicators for the zones you selected and the
STAY indicator are extinguished.
Example
If you want to select zones 2, 5, and 6, enter:
[2 5 8 0 4][AWAY][2][STAY][5][STAY][6][STAY]
[AWAY]
You can disable all zones selected to be automatically
isolated for STAY Mode 2 at any time. To disable
STAY Mode 2 zones:
Enter your Master Code and press [4][AWAY]
[AWAY].
5.2.7 Turning Outputs On/Off
If an output is programmed for remote operation,
you can turn the remote output on or off using this
Master Code function or remotely using the Alarm
Link Software.
To use this Master Code function, you must program
one or more of the outputs with these Output Event
Types:
Output 1 = Output Event Type 2,8 (page 74)
Output 2 = Output Event Type 2,9 (page 74)
Output 3 = Output Event Type 2,10 (page 74)
To turn an output on from the remote codepad:
1. Enter your Master Code and press [5][AWAY].
Three beeps sound and the STAY and AWAY
indicators flash.
2. Enter the number of the output (1 to 3) and press
[AWAY].
Three beeps sound and the output turns on.
3. Repeat Step 2 to turn on another output.
4. Press [AWAY] to exit from this function.
Two beeps sound and the STAY and AWAY
indicators are extinguished.