Filter
Top Products
Table of Contents Teledyne API – Technical Manual - Model 300E Family CO Analyzers
xii
8.1.7. Terminal Operating Modes ................................................................................................................. 156
8.1.7.1. Help Commands in Terminal Mode............................................................................................. 156
8.1.7.2. Command Syntax........................................................................................................................ 157
8.1.7.3. Data Types .................................................................................................................................. 157
8.1.7.4. Status Reporting.......................................................................................................................... 158
8.1.7.5. COMM Port Password Security................................................................................................... 159
8.2. Multidrop RS-232 Set Up ........................................................................................................................... 160
8.3. RS-485 Configuration of COM2 ................................................................................................................. 162
8.4. Remote Access via the Ethernet................................................................................................................ 164
8.4.1. Ethernet Card COM2 Communication Modes and Baud Rate........................................................... 164
8.4.2. Configuring the Ethernet Interface Option using DHCP ..................................................................... 165
8.4.3. Manually Configuring the Network IP Addresses ............................................................................... 167
8.4.4. Changing the Analyzer’s HOSTNAME ............................................................................................... 170
8.5. MODBUS SetUp ........................................................................................................................................ 171
8.5.1. Remote Access by Modem................................................................................................................. 172
8.6. Using the M300E/EM with a Hessen Protocol Network............................................................................. 175
8.6.1. General Overview of Hessen Protocol................................................................................................ 175
8.6.2. Hessen COMM Port Configuration ..................................................................................................... 175
8.6.3. Activating Hessen Protocol................................................................................................................. 176
8.6.4. Selecting a Hessen Protocol Type...................................................................................................... 177
8.6.5. Setting The Hessen Protocol Response Mode................................................................................... 178
8.6.6. Hessen Protocol Gas List Entries ....................................................................................................... 179
8.6.6.1. Gas List Entry Format and Definitions......................................................................................... 179
8.6.6.2. Editing or Adding HESSEN Gas List Entries............................................................................... 180
8.6.6.3. Deleting HESSEN Gas List Entries............................................................................................. 181
8.6.7. Setting Hessen Protocol Status Flags ................................................................................................ 182
8.6.8. Instrument ID Code............................................................................................................................. 183
8.7. APICOM Remote Control Program............................................................................................................ 184
9. CALIBRATION PROCEDURES ....................................................................................... 185
9.1. Before Calibration ...................................................................................................................................... 186
9.1.1. Required Equipment, Supplies, and Expendables ............................................................................. 186
9.1.2. Calibration Gases ............................................................................................................................... 186
9.1.2.1. Zero Air........................................................................................................................................ 186
9.1.2.2. Span Gas..................................................................................................................................... 187
9.1.2.3. Traceability .................................................................................................................................. 187
9.1.3. Data Recording Devices ..................................................................................................................... 187
9.2. Manual Calibration Checks and Calibration of the M300E/EM Analyzer in its Base Configuration .......... 188
9.2.1. Setup for Basic Calibration Checks and Calibration........................................................................... 188
9.2.2. Performing a Basic Manual Calibration Check ................................................................................... 190
9.2.3. Performing a Basic Manual Calibration .............................................................................................. 191
9.2.3.1. Setting the Expected Span Gas Concentration........................................................................... 191
9.2.3.2. Zero/Span Point Calibration Procedure....................................................................................... 192
9.3. Manual Calibration with Zero/Span Valves................................................................................................ 193
9.3.1. Setup for Calibration Using Valve Options ......................................................................................... 193
9.3.2. Manual Calibration Checks with Valve Options Installed ................................................................... 195
9.3.3. Manual Calibration Using Valve Options ............................................................................................ 196
9.3.3.1. Setting the Expected Span Gas Concentration........................................................................... 196
9.3.3.2. Zero/Span Point Calibration Procedure....................................................................................... 197
9.3.3.3. Use of Zero/Span Valve with Remote Contact Closure .............................................................. 198
9.4. Automatic Zero/Span Cal/Check (AutoCal) ............................................................................................... 198
9.4.1. SETUP ACAL: Programming and AUTO CAL Sequence.............................................................. 201
9.4.1.1. AutoCal with Auto or Dual Reporting Ranges Modes Selected .................................................. 203
9.5. CO Calibration Quality ............................................................................................................................... 204
9.6. Calibration of the M300E/EM’s Electronic Subsystems............................................................................. 205
9.6.1. Dark Calibration Test .......................................................................................................................... 205
9.6.2. Pressure Calibration ........................................................................................................................... 206
9.6.3. Flow Calibration .................................................................................................................................. 207
9.6.4. Electrical Test Calibration ................................................................................................................... 208
04288D DCN5752