Bosch Appliances D623 Home Security System User Manual


 
D623 Series/D625 Series | User's Guide | Turn the System Part 2 On (Cmd 3)
12 Bosch Security Systems | 9/04 | 46841E
4. During the last 10 sec. of Exit Delay, the keypad
displays Do not exit! and emits a double tone
every second to warn you not to exit and to turn
the system off. The system turns Part On. The On
indicator remains on steady.
Smiths Residence
Part On
5. To turn the system off, enter your passcode.
Turn the System Part 2 On
(Cmd 3)
Exit Delay Time (to be filled in by your security
company).
You have __________ sec. to exit premises before
system turns on.
I can perform this command.
I cannot perform this command.
Part 2 On turns on the portion of your system
designated as Part 2, leaving the rest of the system
turned off. You can select the points that turn on for
Part 2 On, whereas Part On points are determined by
your security company (refer to Set Part 2 Points (Cmd
65) on page 12). Once you press [CMD] [3], the exit
delay timer countdown begins.
Smiths Residence
Ok for Part On
In the following example, 60 sec, is used as the Exit
Delay. Exit Delay is set by your security company and
may vary from the example shown below.
1. Make sure that points are normal (not faulted).
2. Press [CMD] [3] to turn the system Part 2 On. The
keypad may prompt you to enter a valid passcode.
3. Enter your passcode if necessary. The On indicator
turns on. The keypad display scrolls the following:
60 seconds to
Part 2 On.
To bypass points
Press Bypass.
For no delay
Press No Delay.
For All On
press All On
48 seconds to
Part 2 On.
Enter your passcode to stop the system from
turning on during the exit delay. You can turn the
system Part 2 On with No Delay by pressing [NO
DELAY], or you may bypass points by pressing
the [BYPASS] key.
4. During the last 10 sec. of Exit Delay, the keypad
displays Do not exit! and emits a double tone
every second to warn you not to exit and to turn
the system off. The system turns Part 2 On. The
On indicator remains on steady.
Smiths Residence
Part 2 On
5. Enter your passcode to turn the system off.
Set Part 2 Points (Cmd 65)
I can perform this command.
I cannot perform this command.
Use this command to program which points are armed
each time you turn the system Part 2 On. This lets you
turn part of the system on to detect intrusion, while the
remaining part of the system lets you move freely
without sounding an alarm.
1. Make sure the system is turned off (On indicator is
off).
2. Press [CMD] [6] [5]. The keypad may prompt you
to enter a valid passcode.
3. Enter your passcode if necessary. The keypad
display scrolls the following:
Pt2 Part 2 No
Front Door
Press 2* for
Pt2 Part 2 Yes
Pt3 Part 2 Yes
Hallway
Press 3* for
Pt3 Part 2 No
To exit
Press Cmd.
4. Enter the Point Number followed by the [*] key to
toggle between Yes or No for Part 2 On. Repeat
until all points are programmed Yes or No for Part
2 Mode (Yes = Active, ready to detect intrusion;
No = Non-Active, you can move freely without
sounding an alarm).
5. Press [CMD] to exit this command.
Turn the System On with No
Delay
This command turns the system All On or Part On
without entry or exit delays. Remember that turning
the system on with no delay allows no exit or entry
delay time through the designated delay point, like the
Front Door.
1. Make sure all points are normal (not faulted).