Filter
Top Products
ICP-CC404 | Installation Guide | 16.0 Programmable Outputs
Bosch Security Systems, Inc. | 12/08 | F01U089401-02 69
Table 54: Event Type Polarities
Option Description
0 Output not used
1 Normally open, going low
2 Normally open, pulsing low
3 Normally open, one-shot low
4 Normally open, one-shot low (can restart timer)
5 Normally open, one-shot low (can reset)
6 Normally open, one-shot low (alarm)
7 Normally open, latching low
8 Normally low, going open
9 Normally low, pulsing open
10 Normally low, one-shot open
11 Normally low, one-shot open (can restart timer)
12 Normally low, one-shot open (can reset)
13 Normally low, one-shot open (alarm)
14 Normally low, latching open
0 – Output Not Used
If an output is not required, program the polarity as
0.
1 – Normally Open, Going Low
This polarity is a normally-open circuit and switches
to 0 V when the event occurs. The output switches
back to an open circuit when the event is restored.
Time parameters do not apply to this polarity.
2 – Normally Open, Pulsing Low
This polarity is a normally-open circuit and switches
to pulsing 0 V when the event occurs. The output
switches back to an open circuit when the event is
restored. Time parameters vary the On time of the
pulse.
3 – Normally Open, One-Shot Low
This one-shot polarity is a normally-open circuit and
switches to 0 V when the event occurs. The output
switches back to an open circuit when the time
parameter setting expires. This one-shot time setting
always runs its full duration and cannot be manually
reset.
4 – Normally Open, One-Shot Low with Reactivate
This one-shot polarity is a normally-open circuit and
switches to 0 V when the event occurs. Every time
the event occurs, it restarts the one-shot timer. The
output switches back to an open circuit when the one-
shot time expires.
This polarity is ideally suited for lighting control. You
can use a PIR to activate an output to turn on lights.
Whenever there is movement, the PIR reactivates the
output and lengthens the time the lights remain on.
5 – Normally Open, One-Shot Low with Reset
This one-shot polarity is a normally-open circuit and
switches to 0 V when the event occurs. Because the
output switches back to an open circuit when the one-
shot time expires or when the event returns to
normal, the operation of the output can be shortened
regardless of the programmed time parameter.
6 – Normally Open, One-Shot Low with Alarm
This one-shot polarity is a normally-open circuit and
switches to 0 V when the event occurs. The output
switches back to an open circuit when the one-shot
time expires, when the event returns to normal, or
when the system is disarmed.
This polarity is ideally suited for the operation of
strobe lights because you can program the lights to
reset (up to 99 hours) and prevent them from burning
out or bothering others due to prolonged operation.
7 – Normally Open, Latching Low
This polarity is a normally-open circuit and switches
to 0 V when the event occurs. The output switches
back to an open circuit when a user holds down [7]
on the remote codepad until two beeps sound. Time
parameters do not apply to this polarity.
8 – Normally Low, Going Open
This polarity is normally 0 V and switches to an open
circuit when the event occurs. The output switches
back to 0 V when the event ends. Time parameters
do not apply to this polarity.
9 – Normally Low, Pulsing Open
This polarity is normally 0 V and switches to a
pulsing open circuit when the event occurs. The
output switches back to 0 V when the event ends.
Time parameters vary the Off time of the pulse.
10 – Normally Low, One-Shot Open
This one-shot polarity is normally 0 V and switches to
an open circuit when the event occurs. The output
switches back to 0 V when the time parameter
expires. This one-shot time setting always runs its full
duration and cannot be manually reset.
11 – Normally Low, One-Shot Open with Reactivate
This one-shot polarity is normally 0 V and switches to
an open circuit when the event occurs. Every time the
event occurs, it restarts the one-shot timer. The output
switches back to 0 V when the one-shot time expires.
12 – Normally Low, One-Shot Open with Reset
This one-shot polarity is normally 0 V and switches to
an open circuit when the event occurs. Because the
output switches back to 0 V when the one-shot time
expires or when the event returns to normal, the one-
shot timer can be shortened regardless of the time
setting.