Filter
Top Products
ICP-CC404 | Installation Guide | 9.0 Domestic Dialing
Bosch Security Systems, Inc. | 12/08 | F01U089401-02 41
If a busy tone is not detected, the control panel
assumes that the telephone was answered and sends
its transmission. The transmission sequence consists
of an identification beep, followed by a siren tone and
a long pause. The transmission sequence is repeated
until the control panel receives an acknowledgment
tone during the pause. The control panel
automatically hangs up after 2 min. If more than one
control panel sends reports to the same telephone
number, the identification beep allows the customer
to identify the control panel that called. The
identification beep is programmed in Location 039 of
the Subscriber ID Number for Receiver 1 or
Location 079 of the Subscriber ID Number for
Receiver 2.
When set up for Domestic Dialing Format,
the control panel attempts up to six calls
per alarm event. This count includes any
unsuccessful calls. The counter is reset if
the zone is reactivated and the control
panel attempts six additional calls. The
control panel stops dialing after six
attempts or three successful calls. The
control panel also stops dialing if a valid
User Code is entered at the remote
codepad.
If both Receiver 1 and Receiver 2 are
programmed for domestic dialing, the
maximum number of calls per alarm
event is twelve.
To acknowledge domestic dialing:
If the received call is not acknowledged during any of
the transmission pauses by pressing the [*] button on
a touch-tone telephone or by using the CC911 Phone
Controller, the control panel continues to send its
transmission for 2 min. It then hangs up and dials the
next telephone number. If the call is successfully
acknowledged, the control panel hangs up and makes
no more calls for that event.
9.2 Setting Up and Programming
Domestic Reporting
Programming the control panel for domestic
reporting is extremely simple when using the
Installer’s Programming Command 965. Refer to
Section 2.4.8 Command 965 – Set Up Domestic Dialing
Format on page 13 for more information.
To set up the control panel for domestic dialing:
1. Enter the Installer Code and press [AWAY] to
enter Installer’s Programming Mode.
Two beeps sound and the STAY and AWAY
indicators flash.
2. Enter [9 6 5] and press [AWAY].
Two beeps sound. The control panel is now set
up for Domestic Dialing Format.
3. Enter [9 6 0] and press [AWAY] to exit from the
Installer’s Programming Mode.
Two beeps sound and the STAY and AWAY
indicators turn off. The system returns to the
disarmed state.
4. To program your telephone numbers, enter the
Installer Code and press [2][AWAY].
Three beeps sound and the STAY and AWAY
indicators flash.
If there are telephone numbers already
programmed, they appear one digit at a time
using the codepad indicators.
If there are no programmed telephone numbers,
an additional two beeps sound after entering this
mode. These two beeps normally sound after the
last digit of the last phone number lights.
5. Enter the digits for telephone number 1, one digit
at a time (refer to Table 31).
As you enter each digit, the corresponding
codepad indicator lights.
Table 31: Domestic Dialing Digits
Digit
Required
Number to
Program
Digit
Required
Number to
Program
0 0 8 8
1 1 9 9
2 2 10 refer to 0
3 3 * * 1
4 4 # * 2
5 5 4 sec pause * 3
6 6 break * 4
7 7 15 * 5
6. After you enter all the digits of the first telephone
number, press [STAY][4] to insert a break
between the first telephone number and the
second telephone number.
7. Repeat Step 6 for each additional phone number.
8. After the last digit of the last telephone number,
press [AWAY] to exit from this mode.
Example
To program two separate telephone numbers (9672
1777 and 9672 1233), enter the following sequence:
[1 2 3 4
2][AWAY][9 6 7 2 1 7 7 7][STAY]
[4 9 6 7 2 1 2 3 3][[AWAY]
You can cancel domestic dialing at any time (for
example, you are moving house and do not want the
system to continue calling your work place or mobile
phone).
To disable domestic dialing:
Enter the Installer Code and press
[2][AWAY][STAY][4][AWAY].