Filter
Top Products
Tools Needed:
Power Drill
1/8” Drill Bit
Tape Measure
Pull Rope
DO NOT INSTALL PULL ROPES ON
DOORS WITH ELECTRIC OPERATORS.
CHILDREN MAY BECOME ENTANGLED
IN THE ROPE CAUSING SEVERE OR
FATAL INJURY.
Measure and mark the jamb approximately 48” to 50”
(1220 to 1270 mm) from floor on the right or left side of
jamb. Drill 1/8” pilot hole and install No. 6 screw eye.
Locate the roller carrier at the bottom of the door;
remove the self tapping screw. Using the roller carrier
as a guide, drill a 1/8” diameter hole through the u-bar.
Insert the 1/8” x 3/4” eye bolt and secure to the u-bar
with one nut. Tie pull rope to the eye bolt.
Tie pull rope to No. 6 screw eye , installed on jamb as
shown.
48”- 50” HEIGHT
HEADER
OPERATOR
STRUCTURALLY SOUND
FRAMING MEMBERS
PERFORATED
ANGLES
OPERATOR
RAIL
PERFORATED
ANGLE
OPERATOR
RAIL
SUITABLE MOUNTING
SURFACE (2 X 6)
LUMBER MIN.
DOOR ARM TO
OPERATOR BRACKET
26
Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your
local yellow pages/business listings or go to the Find a Dealer section online at www.wayne-dalton.com
Trolley Operator
OPERATOR MUST BE TESTED AT TIME
OF INSTALLATION AND MONTHLY
THEREAFTER AS DESCRIBED IN YOUR
INSTALLATION INSTRUCTIONS AND
OWNER’S MANUAL, TO ENSURE THAT
DOOR SAFETY FEATURES FUNCTION.
FAILURE TO TEST OR MAKE ANY
NECESSARY ADJUSTMENTS OR REPAIRS,
CAN RESULT IN SEVERE OR FATAL
INJURY.
1. Install operator rail 1/2” to 1-1/2” (13 - 38 mm) above
high arc of top section of the door.
2. Attach operator bracket to a suitable mounting surface
(2” x 6”) lumber minimum.
3. Mount operator to ceiling so that 1” to 1-1/2” (25 - 38
mm) clearance is maintained between trolley rail and
top section when door is fully open (trolley rail will slope
down towards rear).
4. Attach operator to structurally sound ceiling framing
members.
5. Attach door arm to operator bracket.
IMPORTANT: ANGLE MUST BE ATTACHED TO
FRAMING MEMBER(S).
WARNING
WARNING
Tools Needed:
Cleaning
Like any other exterior surface, Wayne-Dalton garage doors will have dirt exposure from atmospheric conditions. Ordinarily, the cleaning action of rainfall will be adequate to
wash the door, or the door can be washed periodically by hosing with a garden hose and clear water (in particular) for the areas not accessible to rain. If you desire to do a
more thorough cleaning, or where soil collection conditions occur, follow these simple instructions.
1. Use a soft-bristled, long-handled washing brush. It attaches to your garden hose and makes washing your garage door easier. Do not rub vigorously which may create
glossy areas over the vinyl finish.
2. For hard-to-remove dirt, such as soot and grime found in industrial areas, wash the garage door down with a mild solution consisting of the following ingredients:
One cup detergent (with less than 0.5% phosphate) dissolved into five gallons of warm water.
NOTE: The use of detergents containing greater than 0.5% phosphate is not recommended for use in general cleaning of garage doors.
NOTE: Be sure to clean behind weather stripping on both sides and top of door.
3. Start at the bottom and work up to the top, as less streaking will result. Immediately following all washing operations, thoroughly rinse the surface area with fresh
water from a garden hose.
This cleaning and maintenance information is suggested in an effort to be of assistance; however, manufacturer cannot assume responsibility for results obtained which
are dependent on the cleaning solution and method of application.
CAUTION: DO NOT PAINT DOOR. PAINTING DOOR WILL VOID YOUR WARRANTY.
JAMB
BOTTOM
SECTION
NO. 6
SCREW EYE
SMALL EYE
BOLT
BOTTOM
SECTION
NUT
SMALL EYE
BOLT
1/8” x 3/4”