Filter
Top Products
83
FX-301
12 to 24 V DCע10 % Ripple P-P 10 % or less
<Red LED / Infrared LED type>
Normal operation: 960 mW or less
Current consumption 40 mA or less at
24 V supply voltage
ECO mode: 600 mW or less
Current consumption 25 mA or less at 24 V
supply voltage
NPN open-collector transistor
•
Maximum sink current:100 mA
50 mA, if five, or more, amplifiers
are connected in cascade.
•
Applied voltage:
30 V DC or less (between output and 0 V)
•
Residual voltage:1.5 V or less
at 100 mA (at 50 mA, if five, or more,
amplifiers are connected in cascade)
sink current.
DC-12 or DC-13
Selectable either Light-ON or Dark-ON, with jog switch
Incorporated
65 !s or less (ultra high speed), 150 !s or less (FAST), 250 !s or less [STD / S-D (Red LED type only)], 2 ms or less (LONG) selectable with jog switch
2-level teaching / Limit teaching / Manual adjustment / Full auto-teaching (excluding red LED type)
Orange LED (lights up when the output is ON)
Green LED (lights up under stable light received condition or stable dark condition)
RUN: Green LED, TEACH ⅐ ADJ ⅐ L/D ON ⅐ TIMER ⅐ PRO:Yellow LED
4 digit red LED display
Incorporated
Incorporated with variable ON-delay / OFF-delay / ONE SHOT timer, switchable either effective or ineffective. (timer period:0.5 to 500 ms approx.)
Incorporated (Up to four sets of fiber heads can be mounted close together) (Note 1)
3 (Industrial environment)
מ10 to ם55 °C ם14 to ם131 °F
If 4 to 7 units are connected in cascade:
מ10 to ם50 °C ם14 to ם122 °F,
if 8 to 16 units are connected in cascade:
מ10 to ם45 °C ם14 to ם113 °F
(No dew condensation or icing allowed),
Storage:
מ20 to ם70 °C מ4 to ם158 °F
35 to 85 % RH, Storage: 35 to 85 % RH
Sunlight: 10,000?x at the light-receiving face, Incandescent light: 3,000?x at the light-receiving face
Red LED type: EN 50081-2, EN 50082-2, EN 60947-5-2
Blue / green / infrared LED type: EN 60947-5-2
1,000 V AC for one min. between all supply terminals connected together and enclosure (Note 2)
20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure (Note 2)
10 to 150 Hz frequency, 0.75 mm 0.030 in amplitude in X, Y and Z directions for two hours each
98 m/s
2
acceleration (10 G approx.) in X, Y and Z directions for five times each
Enclosure: Heat-resistant ABS, Case cover: Polycarbonate, Switch: Acrylic
Connector (Note 3)
Extension up to total 100 m 328.084 ft is possible with 0.3 mm
2
, or more, cable.
25 g approx.
Supply voltage
Power consumption
Output
Utilization category
Output operation
Short-circuit
protection
Response time
Sensitivity setting
Operation indicator
Stability indicator
MODE indicator
Digital display
Fine sensitivity adjustment function
Timer function
Automatic interference prevention function
Ambient temperature
Ambient humidity
Ambient illuminance
EMC
Voltage withstandability
Insulation resistance
Vibration resistance
Shock resistance
Emitting element (modulated)
Material
Connecting method
Cable extension
Weight
SPECIFICATIONS
Amplifiers
Type
Model No.
NPN output PNP output
Red LED Blue LED Green LED Infrared LED Red LED Blue LED Green LED
Infrared LED
FX-301 FX-301B FX-301G FX-301H FX-301P FX-301BP FX-301GP FX-301HP
Item
Environmental resistance
Red LED Blue LED Green LED Infrared LED Red LED Blue LED Green LED
Infrared LED
Notes: 1) When the power supply is switched on, the emission timing are automatically set for interference prevention.
Notes: 2) The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.
Notes: 3) The cable for amplifier connection is not supplied as an accessory. Make sure to use the optional quick-connection cable given below.
Main cable (3-core): CN-73-C1 (cable length 1 m 3.281 ft), CN-73-C2 (cable length 2 m 6.562 ft), CN-73-C5 (cable length 5 m 16.404 ft)
Sub cable (1-core): CN-71-C1 (cable length 1 m 3.281 ft), CN-71-C2 (cable length 2 m 6.562 ft), CN-71-C5 (cable length 5 m 16.404 ft)
PNP open-collector transistor
• Maximum source current: 100 mA
50 mA, if five, or more, amplifiers
are connected in cascade.
•
Applied voltage:30 V DC or less (between output and םV)
• Residual voltage:1.5 V or less
at 100 mA (at 50 mA, if five, or more,
amplifiers are connected in cascade)
source current.
<Blue LED / Green LED type>
Normal operation: 720 mW or less
Current consumption 30 mA or less at
24 V supply voltage
ECO mode: 430 mW or less
Current consumption 18 mA or less at 24 V
supply voltage
()()
()
()
()( )
Pollution degree
)(
08/2005