5
USER INSTRUCTIONS
• PressandholdtheDOWNarrowtodecreaseto
minimum
At the lowest point the fire goes to 'standby mode' (only
pilot lit)
Note: While pressing a button, a symbol indicating
transmission appears on the display. The receiver
confirms transmission with an acoustic signal.
Turning the Studio Off
• PresstheOFFbuttontoextinguishthepilot
2.3 TEMP MODE
The display shows the current room temperature.
To increase or decrease the fire’s output:
• PresstheSETbuttontoselecteithertheDAYTEMP
or the NIGHT TEMP mode by briefly pressing the
SET button
• HoldtheSETbuttonuntiltheTEMPdisplayflashesand
then let go
• SetthedesiredtemperaturewiththeUPandDOWN
arrows. (Minimum temperature 5C, maximum 30C or
41F to 86F when fahrenheit is the preferred option)
• PresstheOFFbuttontostopthedisplayflashingorwait
to return to TEMP mode.
NOTE: If you set a temperature that is beneath the
current room temperature, the fire automatically
switches to OFF.
NOTE: If you would like the Night temperature control to
turn off then decrease the temperature until [---] is
displayed.
2.4 TIMER MODE
There are two programmable settings you can make over a
24 hour period, P1 and P2.
P1 +
= Start Timed Setting 1
P1 +
= End of Timed Setting 1
P2 +
= Start Timed Setting 2
P2 +
= End of Timed Setting 2
2.4.1 P1 - Program 1 for a Timed Setting
• PresstheSETbuttonuntiltheTIMERmodeisdisplayed
• HoldtheSETbutton.Thedisplaysflashesthecurrent
time for P1. While the time displayed is flashing you can
alter the hours and minutes set.
To set the time your fire first lights, change P1
•PresstheUParrowtoalterthehour
•PresstheDOWNarrowtoaltertheminutes
in 10 minute increments
•PressSETagaintomovetotheendsettingfor
P1
This is the time your Studio first shuts down:
•PresstheUParrowtoalterthehour
•PresstheDOWNarrowtoaltertheminutes
2.4.2 P2 - Program 2 for a Timed Setting
Use the same steps outlined in 2.4.1 to change the setting
for P2.
If you have already set P1 and want to alter the setting for
P2 only:
• PresstheSETbuttonuntilTIMERmodeisdisplayed
•HoldtheSETbuttonuntil the display flashes the
current time for P1
•PresstheSETbuttononceagaintoscrollpastthesettings
for P1
and P1
Withthetimestillflashing:
•PresstheUParrowtoalterthehour
•PresstheDOWNarrowtoaltertheminutes
OnceallfourtimesaresetpresstheOFFbuttonorsimply
wait to complete programming.
2.5 LOW BATTERY
“BATT” is displayed on the remote when its batteries need
replacement.
2.6 SETTING THE TIME
• SimultaneouslypresstheUPandDOWNarrowbuttons
• Presstheupbuttontosetthehourandthedownbutton
to set the minutes
• PressOFFtoreturntothemanualmodeorsimplywait
2.7 SETTING THE °C/24 HOUR OR °F/12 HOUR CLOCK
• PressOFFandthedownarrowuntilthedisplaychanges
from °C/24 hour clock to °F/12 hour clock and vice
versa.
If the remote is removed, lost or damaged, signals
transmitted to the receiver cease. Your fire will go to
standby (pilot) mode after 6 hours.
2B - TOUCH PAD CONTROL
2
AR1887
• PresstheON-OFFbuttontolighttheappliance,(upto
30 seconds)
• PresstheUPbuttontoincreasetheflameheight
• PresstheDOWNbuttontodecreasetheflameheight.At
the lowest point it goes to ‘standby mode’, (only pilot
lit)
• PresstheON-OFFbuttontoturntheapplianceoff