Filter
Top Products
– 12 –
∗
∗∗
∗93
Reports In Armed Period Per
Zone
(Swinger Suppression)
Restrict Report Pairs:
0 = Unlimited Reports
1 = 1 report pair per zone per armed
period
2 = 2 report pairs per zone per armed
period
SIA-Compliant Controls:
Restrict Report Pairs:
1 = 1 report pair; 2 = 2 report pairs
Unlimited Reports Enable:
0 = restrict reports to the setting in
entry 1
1 = unlimited reports for zones listed
in zone list 7; (use zone list 7 to
enter those zones that require
unlimited reporting; these zones
ignore the setting in entry 1)
[1,0]
Restrict SIA-Compliant Controls:
Report Pairs Unlimited Reports Enable
Selection limits the number of alarm/alarm restore message pairs per
zone sent to the CS in an armed period. Swinger suppression applies
to burglary zones only.
SIA Guidelines: Must be set for option 1 or 2
DOWNLOAD INFORMATION (
✱
94,
✱
95)
∗
∗∗
∗94
Download Phone No.
Enter up to 20 digits, 0–9; #+11 for '
✱
';
#+12 for '#'; #+13 for a 2-second pause.
Do not fill unused spaces. If fewer than
20 digits, exit field by pressing
✱
. To
clear entries from field, press
✱
94
✱
.
| | | | | | | | | | | | | | | | | | |
Enter the phone number of the downloading computer.
UL: downloading may be performed only if a technician is at the site.
Up/downloading via the Internet has not been evaluated by UL.
∗
∗∗
∗95
Ring Count For Downloading
0 = Disable Station Initiated Download;
1–14 = number of rings (1–9, # +10 =10,
# +11 =11, # +12 =12, # +13 =13,
# +14 =14);
15 = answering machine defeat
(# +15 =15).
NOTE: Do not enter 0 if using 4286
Phone Module.
[15]
Refer to the chart below and program accordingly.
phone answer down-
module machine loading Set field ∗
∗∗
∗95 to…
yes no no 1-14 (not 0)
yes yes no greater than rings set on answer machine
(e.g., if ans. machine is 4 rings, set this
field to 5). This allows access to the
phone module if the answer machine is
off.
yes no yes 1-14 (not 0)
yes yes yes 15 (bypasses answer machine
†
)
no no no 0
no yes no 0
no no yes 1-14
no yes yes 15
† NOTE: If “15” is entered to bypass an answering machine, and a 4286
Phone Module is included in the system, you should note the following:
When calling in from an off-premises phone, the user should make the initial
call, allow 1 or 2 rings only, then hang up, then call again. The phone module
will now seize the line, and 2 long tones sound, followed by the usual voice
prompt for the access code. If this procedure is not followed, phone module
operation will not be possible.
∗
∗∗
∗96, ∗
∗∗
∗97 Initialize/Reset Defaults (
These are commands, not data fields. See page 3.)
∗
∗∗
∗98, ∗
∗∗
∗99 Exit Commands (
These are commands, not data fields. See page 3.)
PAGER OPTIONS (✱160- ✱172)
The system can send various reports to several pagers (FA168CPS = up to 4; FA148CP = up to 2).
To program pager reporting, do the following:
1. Enter the pager phone number(s), preface characters, and pager report options in data fields *160 - *171.
2. Enable Pager Delay, if desired, in field *172 (delays alarm reporting for ALL pagers).
3. Make sure appropriate user open/close pager reports are enabled (see Security Codes section in User Guide). Users
that perform actions in partition 1 will, if enabled, attempt to report to all pagers enabled for open/close reporting in
partition 1. Users that perform actions in partition 2 will, if enabled, attempt to report to all pagers enabled for open/close
reporting in partition 2.
4. If using latchkey pager report, define the latchkey report schedule using Scheduling mode (master code + [#] [6] [4] then
select event type
03
). System must be armed for the Latchkey report to be sent.
5. If using a function key to manually send a message to a pager, use *57 Function Key Menu mode to define the key
(function
01
).
6. If reporting zone alarms and troubles to a pager, use *81 Zone List menu mode to assign the zones associated with each
pager (zone lists 9-12
†
).
† FA148CP supports zone lists 9 and 10 only.