Filter
Top Products
67
Chapter 7: Programming
POUND OR ASTERISK: When dialing to a beeper, a pound sign (#) or an asterisk (*)
may be used within the phone number. When using pulse dialing, the # or * will instruct
ISACC to switch to tones for the remaining digits.
Example: 1 # 6105554591 A P 986033 #
NOTE: When dialing to a beeper it is sometimes necessary to combine codes. Certain
beeper systems vary and you must adjust accordingly. To test your beeper system, use an
extension telephone on the same line as the ISACC unit and listen in during ISACC's dial
out to confirm that your beeper service is reached without a problem. If you must add a
pause, use the letter P to insert a two second pause wherever necessary. See your beeper
service for specifics.
SELECTION
This keyword command allows you to program ISACC to dial only specific phone numbers
depending on which input is in alarm.
To display the current dialing selection, type show selection after an ISACC prompt. You
may also display the selection for a specific phone number by typing show selection followed
by the entry number (01-08).
ISACC>show selection
DIALOUT ALARM SELECTION
Input source = 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16
PH01 = "Engineer Beeper " = 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
PH02 = "DIF phone " = 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
PH03 = "Office " = 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
PH04 = "Manager " = 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
PH05 = "M.Weaver " = 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
PH06 = "J. Hogan " = 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
PH07 = "A. Daniels " = 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
PH08 = "M. Otto " = 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
To change the dialing selection for each phone number, type set selection after an ISACC
prompt. Enter 1 to enable or 0 (zero) to disable the alarm dialing for the corresponding phone
number and input. Press the spacebar to advance to the next entry. Press ENTER to jump to
the next phone number. You may also program the selection of a specific phone number by
typing set selection followed by the entry number(01-08).
ISACC>set selection
DIALOUT ALARM SELECTION
Input source = 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16
PH01 = "Engineer Beeper " = 1 1 0 0 0 1 0 1 0 0 0 0 0 0 0 0
PH02 = "DIF phone " = 1 1 0 0 0 1 0 1 0 0 0 0 0 0 0 0
PH03 = "Office " = 1 1 0 0 0 1 0 1 0 0 0 0 0 0 0 0
PH04 = "Manager " = 0 0 1 1 1 0 1 0 1 1 1 1 1 1 1 1
PH05 = "M. Weaver " = 0 0 1 1 1 0 1 0 1 1 1 1 1 1 1 1
PH06 = "J. Hogan " = 0 0 1 1 1 0 1 0 1 1 1 1 1 1 1 1
PH07 = "A. Daniels " = 0 0 1 1 1 0 1 0 1 1 1 1 1 1 1 1
PH08 = "M. Otto " = 0 0 1 1 1 0 1 0 1 1 1 1 1 1 1 1