Filter
Top Products
35
ENVISION CONSOLE INSTALLATION MANUAL
Point Type Point Address Long Name
ADF 1 nciSetpoints.Occupied_Co Occupied Cooling Setpoint Input (Read/Write)
ADF 2 nciSetpoints.Standby_Coo Standby Cooling Setpoint Input (Read/Write)
ADF 3 nciSetpoints.Unoccupied_ Unoccupied Cooling Setpoint Input (Read/Write)
ADF 4 nciSetpoints.Occupied_He Occupied Heating Setpoint Input (Read/Write)
ADF 5 nciSetpoints.Standby_Hea Standby Heating Setpoint Input (Read/Write)
ADF 6 nciSetpoints.Unoccupi5#6 Unoccupied Heating Setpoint Input (Read/Write)
ADF 7 nciMinClgSetpt Minimum Cooling Setpoint Input (Read/Write)
ADF 8 nciMaxHtgSetpt Maximum Heating Setpoint Input (Read/Write)
ADF 9 nvoSpaceTemp Space or Zone Temperature Value (Read Only)
ADF 10 nvoDischAirTemp Discharge Air Temp Field Supplied Only (Read Only)
ADF 11 nvoEffClgSetpt Effective Cooling Setpoint Value (Read Only)
ADF 12 nviSpaceTemp Space or Zone Temperature Value Override(Write)
ADF 64 nvoEffHtgSetpt Effective Heating Setpoint Value (Read Only)
ADF 54 nciAux5LevP Dehumidification Setpoint (Read/Write)
ADF 15 nciAux1Temp Heating Freeze Protection Temperature Setpoint Value (Read/Write)
ADF 16 nciAux2Temp Heating Freeze Protection Temperature Setpoint Value (Read/Write)
ADF 17 nvoUnitStatus.Heat_Outpu 1st Stage Compressor Heating Output (Read Only)
ADF 19 nvoUnitStatus.Cool_Outpu 1st Stage Compressor Cooling Output (Read Only)
ADF 21 nvoUnitStatus.Fan_Output Fan Output (Read Only)
BD 9 nvoUnitStatus.Mode Unit Mode of Operation (Read Only)
BD 10 nvoUnitStatus.In_Alarm Unit Alarm mode (Read Only)
ADF 22 nciPropBand Heating/Cooling Prop Band Input (Read/Write)
ADF 23 nciRemoteSetptSpan Warm/Cool Adjust Span (Read/Write)
ADF 24 nciRemoteSetptBias Warm/Cool Adjust Offset Value (Read/Write)
ADF 27 nciTempOffset Space or Zone Temperature Sensor Calibration Input (Read/Write)
ADF 32 nviSetpoint General Setpoint Input (Read/Write)
ADF 39 nvoHtgFrzPro1Tmp Heating Freeze Sensing Temperature Value (Read Only)
ADF 40 nvoHtgFrzSetpt Heating Freeze Sensing Temperature Setpoint Value (Read Only)
ADF 41 nvoAlarms
Alarms Enumerated [0=no alarms, 1=condensate alarm, 2=Compressor Hi Discharge
Pressure alarm, 3=Compressor low Suction Pressure alarm, 4=Freeze sensing
alarm, 8=Faulty Freeze Sensor alarm,
9=Loss of Charge]
(Read Only)
ADF 62 nvoPWMOut ECM PWM Control signal value (Read Only)
ADF 65 nvoECMOvrd ECM PWM Control signal Override (Read/Write)
ADF 63 nvoHumidity Space Humidity value (Read Only)
ADF 66 nviAO2 Spare PWM Output AO2 Command (Write)
ADF 67 nvoAO2 Spare PWM Output AO2 Value (Read Only)
ADI 2 nciBypassTime Temporary Occupancy Time Period Input (Read/Write)
BD 1 nvoEffectOccup Effective Occupancy State (Read Only)
BD 2 nviOccManCmd Occupancy Override Command Input (Read/Write)
BD 4 nviEmergOverride Emergency Override Input (Read/Write)
BD 5 nvoFanStatus Fan Output Status (Read Only)
BD 6 nvoAccStatus Accessory 2 Output Status (Read Only)
BD 7 nvoLP_WVStatus Accessory 1 Output Status (Read Only)
BD 8 nvoAlarmStatus Alarm Output Status (Read Only)
BD 12 nviAlarmReset Alarm Reset Input (Read/Write)
BD 13 nviFanSpeedCmd.State Network equivelant of a thermostatic 'G' call. (Write)
BD 14 nviComprEnable.State Network equivelant of a thermostatic 'Y1' call. (Write)
BD 46 nviY2HiSpeed.State Network equivelant of a thermostatic 'Y2' call. (Write)
BD 18 nvoRV1Status Reversing Valve Output Status (Read Only)
BD 22 nviOccSchedule.Current_s Occupancy Supervisory Scheduler Command Input (Read/Write)
BD 25 nvoCompFanProv Compressor/Fan Proving Switch Status (Read Only)
BD 24 nvoDirtyFilter Dirty Filter Switch Status (Read Only)
BD 26 nvoComp2Status Compressor Hi Capacity Command Status (Read Only)
BD 42 nviBO5 Command for output BO5 used for Emg Heat-Interlocked with Fan DP9Read/Write)
BD 41 nviBO9 Command for output BO9(Read/Write)
BD 47 nvoBO5 Value output for BO5 used for Emg Heat (Read Only)
BD 48 nvoBO9 Value output for BO9 (Read Only)
BD 44 nviDehumEna.State Dehumidification command-like a Humidistat (Read/Write)
Point Description
N2 Open
N2
Envision Console Controls