Filter
Top Products
23
Tools Needed:
Tools Needed:
Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your
local yellow pages/business listings or go to the Find a Dealer section online at www.wayne-dalton.com
INSTALLATION
Cable Drum
No space between Ratchet
Pawl and Cable Drum
indicates engagement
Cable Drum
Ratchet Pawl
ENGAGED SIDE VIEW
No space between
Ratchet Pawl and
Cable Drum
ENGAGED UNDERNEATH VIEW
Space between Ratchet Pawl
and Cable Drum
non-indicates engagement
Cable Drum
Ratchet Pawl
DISENGAGED SIDE VIEW
No space between
Ratchet Pawl and
DISENGAGED U
NDERNEATH VIEW
UPPER POSITION
LOWER POSITION
LOWER POSITION SIDE VIEW
UPPER POSITION SIDE VIEW
Ratchet Pawl in Lower Position
Ratchet Pawl in Upper Position
Use these Illustration, in conjunction with the Instructions on the other side of
this label.
W A RNING
Rachet Bracket is under
EXTREME SPRING
TENSION
.
To avoid possible severe or
fatal injury,
DO NOT
remove
fasteners from ratchet bracket
until spring(s) are fully
wnwound.
To safely unwind spring(s)
read
and follow the directions in the
installation instructions/owners
manual.
DO NOT REMOVE THIS TAG.
RIGHT END
BRACKET
RATCHET WHEEL
(TEETH POINTING
UPWARDS)
Cab
le Drum
No s
pace between
Ratche
t
Pawl and Cable Drum
indicates engagement
Cab
le D
rum
Ratchet
Pawl
ENGAGE
D SIDE VIEW
No s
pace
between
Ratchet Pawl
and
Cable Drum
ENGAGED
UNDERNE
A
T
H VIEW
Spac
e between Ratchet P
awl
and C
able Drum
non-indicates engage
ment
Cab
le Drum
Ratchet Pawl
DISE
NGA
GED
SIDE VIEW
No s
pace
betwe
en
Ratc
het Pawl and
DISENGA
GED U
NDERNEA
TH VIEW
UPPER
POSI
TION
LOW
ER POSITION
LOW
ER POSITION
SIDE VIEW
UPPER POSI
TION
SIDE VIEW
Ratc
het
Pawl
in Lower
Position
Ratc
het Pa
wl
in U
pper Po
sition
Use these Illus
tration, in c
onj
unction with the In
structions on the other
side of
this label.
WARNING
Rachet Bracket is under
EXTREME SPRING
TENSION
.
To avoid possible severe or
fatal injury,
DO NOT
remove
fasteners from ratchet bracke
t
until spring(s) are fully
wnwound.
To safely unwind spring(s)
read
and follow the directions in the
installation instructions
/owners
manual.
DO NOT REMOVE THI
S TAG.
5/16” X 1-5/8”
HEX HEAD LAG
5/16”-18 x 3/4”
CARRIAGE BOLT
5/16”-18 HEX NUT
BLACK TOOTH
End Brackets Continued...
23
CENTER
BRACKET
BUSHING
ASSEMBLY
(2) 5/16” X 1-5/8”
HEX HEAD LAG
SCREWS
NOTE: If you are not installing the
idrive
®
opener on your garage door, you
must install the center bracket bushing
assembly, follow these instructions.
To locate the center bracket, mark the
header halfway between the flagangles
and level the TorqueMaster
®
spring tube.
Drill 3/16” pilot holes into header for the
lag screws. Fasten the metal bracket to
the header using (2) 5/16” X 1-5/8” lag
screws.
Securing Center Bracket
Assembly
Power Drill
3/16” Drill Bit
7/16” Socket
Driver
Step Ladder