Filter
Top Products
Tools Needed:
32
Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your local
yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com
To adjust spring(s), only add or remove a
maximum of 3/10 of a turn (three teeth of
ratchet wheel) at a time. Both sides need
to be adjusted equally on double spring
doors.
NOTE: Single spring applications require
no spring winding on left hand side.
Clamp a pair of vice clamps on the vertical
tracks just above the second roller on one
side and just below the second roller on
the other side. This will prevent the door
from raising or lowering while adjusting
the spring(s).
PRIOR TO WINDING OR MAKING
ADJUSTMENTS TO THE SPRINGS, ENSURE
YOU’RE WINDING IN THE PROPER
DIRECTION AS STATED IN THE
INSTALLATION INSTRUCTIONS.
OTHERWISE THE SPRING FITTINGS MAY
RELEASE FROM SPRING IF NOT WOUND
IN THE PROPER DIRECTION AND COULD
RESULT IN SEVERE OR FATAL INJURY.
To Add Spring Tension: The ratchet
wheel is made of 10 teeth. To add spring
tension, ensure the ratchet and socket is
set so that it will tighten counter clockwise
on the right hand side, and clockwise on
the left hand side. Place the ratchet with
5/8” socket onto the winding shaft, pull
down to add 3/10 of a turn. Watch as
three teeth of the ratchet wheel pass over
the pawl, creating three “clicks”.
To Remove Spring Tension: To remove
spring tension, ensure the ratchet and
socket is set so that it will tighten counter
clockwise on the right hand side and
clockwise on the left hand side. Place the
wrench onto the winding shaft. Pull down
on the ratchet to relieve pressure between
the pawl and the ratchet wheel. Push in on
the pawl to allow the three ratchet wheel
teeth to pass by the pawl, as you carefully
allow the ratchet wrench to be rotated
upward by the spring tension. Release the
pawl to allow it to engage with the ratchet
wheel.
Remove the vice clamps from the vertical
tracks, re-check door balance and adjust
if necessary. When door is balanced and
adjusted properly, place the ratchet pawl
knobs in the active position (lower
position).
TorqueMaster
®
Plus Reset
Instructions Continued...
TRACK
VICE CLAMPS
ATTACHED TO
TRACK
PLACE VICE CLAMPS
ABOVE 3RD ROLLER ON
BOTH VERTICAL TRACK
PAWL KNOB IN LOWER
POSITION
LOWER POSITION
UPPER POSITION
Cable Drum
No space between Ratchet
Pawl and Cable Drum
indica
tes engagement
Cable Dr
um
Ratchet Pawl
ENGAGED SIDE VIEW
No space between
Ratchet Pawl and
Cable Drum
ENGAGED UNDERNEATH VIEW
Space between Ratchet Pawl
and Cable Drum
non-indicates engagement
Cable Drum
Ratchet Pawl
DISENGAGED
SIDE VIEW
No space between
Ratchet Paw
l and
DISENGAGED U
NDERNEATH VIEW
UPPER POSITION
LOWER POSITION
LOWER POSITION SIDE VIEW
UPPER POSITION SIDE VIEW
Ratche
t Pawl in Lo
wer Position
Ratchet Pawl in Upper Position
Use these Illustration, in conjunction with the Instructions on the other side of
this label.
WARNING
Rachet Bracket is under
EXTREME SPRING
TENSION
.
To avoid possible severe or
fatal injury,
DO NOT
remove
fasteners from ratchet bracket
until spring(s) are fully
wnwound.
To safely unwind spr
ing(s)
read
and follow the directions in the
installation instructions/owners
manual.
DO NOT REMOVE THIS TAG.
RATCHET
WITH 5/8”
SOCKET
END BRACKET
3” EXTENSION
PAWL KNOB IN UPPER
POSITION
PAWL
WARNING