Filter
Top Products
Cleaning Your Garage Door
IMPORTANT: DO NOT USE A PRESSURE WASHER ON YOUR GARAGE DOOR!
While factory-applied finishes on garage doors are durable, it is desirable to clean them on a
routine basis. Some discoloration of the finish may occur when a door has been exposed to
dirt-laden atmosphere for a period of time. Slight chalking may also occur as a result of direct
exposure to sunlight.
Cleaning the door will generally restore the appearance of the finish. To maintain an aesthetically
pleasing finish of the garage door, a periodic washing of the garage door is recommended.
THE FOLLOWING CLEANING SOLUTION IS RECOMMENDED:
A mild detergent solution consisting of one cup detergent (with less than 0.5% phosphate) dis-
solved into five gallons of warm water will aid in the removal of most dirt.
NOTE: The use of detergents containing greater than 0.5% phosphate is not recommended for
use in general cleaning of garage doors.
NOTE: Be sure to clean behind weatherstrips on both sides and top of door.
CAUTION: NEVER MIX CLEANSERS OR DETERGENTS WITH BLEACH.
GLASS CLEANING INSTRUCTIONS
Clean with a mild detergent solution (same as above) and a soft cloth. After cleaning, rinse
thoroughly.
ACRYLIC CLEANING INSTRUCTIONS
Clean acrylic glazing with nonabrasive soap or detergent and plenty of water. Use your bare
hands to feel and dislodge any caked on particles. A soft, grit-free cloth, sponge or chamois may
be used to wipe the surface. Do not use hard or rough cloths that will scratch the acrylic glazing.
Dry glazing with a clean damp chamois.
NOTE: Do not use any window cleaning fluids, scouring compounds, gritty cloths or solvent-
based cleaners of any kind.
Painting Your Garage Door
Painting Instructions For Steel and Wood Doors.
Steel (Surface Preparation for Painting)
Wax on the surface must be removed or paint peeling/flaking will result. To remove this wax,
it will be necessary to lightly scuff the surface with a fine steel wool pad, saturated with soapy
water. A final wipe and rinse should be done with clean water only, to remove any loose particles
and any soapy film residue.
Surface scratches, which have not exposed the metal substrate, can be lightly buffed or sanded
with 0000 steel wool or No. 400 sand paper to create a smoother surface. Care must be taken
to not expose the substrate under the paint. Once the substrate is exposed, the likelihood for
rusting is greatly increased.
If substrate is exposed, it must be treated to prevent rust from forming. Sand the exposed area
lightly and paint with a high quality metal primer, specifically intended for galvanized surfaces,
to protect the area from corrosion. Follow the drying time on primer can label before applying
topcoat. The surface of the factory-applied finish, that is being painted, must not be too smooth,
or the paint will not adhere to it. It is advisable to test in an inconspicuous area, to evaluate
adhesion. If poor adhesion is observed, surface preparation for painting thefactory-applied finish,
must be repeated until desired results are achieved. Again, care must be taken to not expose the
substrate under the paint.
Steel (Painting)
After surface has been properly prepared, it must be allowed to dry thoroughly, then coated
immediately with a premium quality latex house paint. Follow paint label directions explicitly. Oil
base or solvent base paints are not recommended. Please note that if substrate is exposed and
not properly primed, painting with latex paint may cause accelerated rusting of the steel in the
exposed area.
NOTES:
1. Repainting of finish painted steel doors cannot be warranted, as this condition is totally
beyond the door manufacturer’s control.
2. Consult a professional coatings contractor if in doubt about any of the above directions.
3. Follow directions explicitly on the paint container labels for proper applications of coatings and
disposal of containers. Pay particular attention to acceptable weather and temperature condi-
tions in which to paint.
Wood (Preparation and Painting)
These instructions apply to all Wood Doors produced and sold by Wayne-Dalton. The exterior
surfaces, as well as all edges must be properly painted and maintained if satisfactory perfor-
mance is to be achieved. The purpose for painting is to both protect and beautify the substrates.
These requirements for finishing are intended to achieve both functions for reasonable service
life of wood doors. Wood doors must be completely finished prior to installation, to ensure that
the interior and exterior surfaces, as well as all edges of the doors are properly protected against
moisture or other contaminants. Wood doors, in a non-finished condition, must not be trans-
ported or stored where the wood surfaces can be exposed to moisture or other contaminants.
Wood (Surface Preparation)
All surfaces must be clean, free of dust and dirt and any other contamination.
Wood (Painting)
Using painter’s tape, tape off all metal surfaces. A premium quality latex house based finish
paint is recommended for use over the factory latex based primer
Painting the wood surfaces with at least 2 coats of finish paint over the primer. Follow paint
manufacture’s label directions completely for all coatings. Once finished, remove painter’s tape
and touch up where necessary.
Wood (Maintenance and Refinishing)
Yearly inspection of all the wood surfaces of the garage door(s) will reveal the extent of weather-
ing and the need for refinishing. When the finish becomes eroded or thin, clean and prime the
areas of deterioration. Follow up with a complete refinishing of the door(s), according to the
above directions, as well as the manufacturer’s label directions. Protecting the door(s) from
prolonged exposure to moisture and sunlight is vital in extending the service life of your garage
door(s).
Operation and Maintenance
OPERATING YOUR GARAGE DOOR…
Before you begin, read all warning labels affixed to the door and the installation instructions and
owner’s manual. When correctly installed, your Wayne-Dalton door will operate smoothly. Always
operate your door with controlled movements. Do not slam your door or throw your door into the
open position, this may cause damage to the door or its components. If your door has an electric
opener, refer to the owner’s manual to disconnect the opener before performing manual door
operation below.
MANUAL DOOR OPERATION:
For additional information on manual garage door operations go to www.dasma.com and refer-
ence TDS 165.
IMPORTANT: DO NOT PLACE FINGERS OR HANDS INTO SECTION JOINTS WHEN OPENING
AND/OR CLOSING A DOOR. ALWAYS USE LIFT HANDLES/ SUITABLE GRIPPING POINTS WHEN
OPERATING THE DOOR MANUALLY.
OPENING A DOOR: Make sure the lock(s) are in the unlocked position. Lift the door by using the
lift handles/ suitable gripping points only. Door should open with little resistance.
CLOSING A DOOR: From inside the garage, pull door downward using lift handles/ gripping
point only or a high friction area only. If you are unable to reach the lift handles/ suitable gripping
points only, use pull rope affixed to the side of door. Door should close completely with little
resistance.
USING AN ELECTRIC OPENER:
IMPORTANT: PULL ROPES MUST BE REMOVED AND LOCKS MUST BE REMOVED OR MADE
INOPERATIVE IN THE UNLOCKED POSITION.
When connecting a trolley type garage door opener to this door, an opener and/or trolley bracket
must be securely attached to the top section of the door, along with any u-bars provided with
the door. Always use the opener and/or trolley bracket supplied with the door. To avoid possible
damage to your door, Wayne-Dalton recommends reinforcing the top section on models 8000,
8100, 8200 and 9100 doors with a u-bar (may or may not be supplied). The installation of the
opener must be according to manufacturer’s instructions and force settings must be adjusted
properly. Refer to the owner’s manual supplied with your electric opener for complete details on
installation, operation, maintenance and testing of the opener.
MAINTAINING YOUR GARAGE DOOR…
Before you begin, read all warning labels affixed to the door and the installation instructions
and owner’s manual. Perform routine maintenance steps once a month, and have the door
professionally inspected once a year. Review your Installation Instructions and Owner’s Manual
for the garage door. These instructions are available at no charge from Wayne-Dalton, A Division
Of Overhead Door Corporation, P.O. Box 67, Mt. Hope, OH., 44660, or online at www.Wayne-
Dalton.com. For additional information on garage door/opener maintenance go to www.dasma.
com and reference TDS 151, 167 and 179.
MONTHLY INSPECTIONS:
1. Visual Inspection: Closely inspect jambs, header and mounting surface. Any wood found not
to be structurally sound must be replaced. Inspect the springs, cables, rollers, pulleys, back
hangs and other door hardware for signs of worn or broken parts. Tighten any loose screws
and/or bolts. Check exterior surface of the door sections for any minor cracks. Verify door has
not shifted right and/or left in the opening. If you suspect problems, have a trained door system
technician make the repairs.
WARNING WARNING
GARAGE DOOR SPRINGS, CABLES, BRACKETS, AND OTHER HARDWARE AT-
TACHED TO THE SPRINGS ARE UNDER EXTREME TENSION, AND IF HANDLED
IMPROPERLY, CAN CAUSE SEVERE OR FATAL INJURY. ONLY A TRAINED DOOR
SYSTEMS TECHNICIAN SHOULD ADJUST THEM, BY CAREFULLY FOLLOWING
THE MANUFACTURER’S INSTRUCTIONS.
17
Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer,
refer to your local yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com
Maintenance