Filter
Top Products
20
Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your
local yellow pages/business listings or go to the Find a Dealer section online at www.wayne-dalton.com
Tools Needed:
20
IMPORTANT: RIGHT AND LEFT HAND
IS ALWAYS DETERMINED FROM INSIDE
THE GARAGE LOOKING OUT.
Shake the TorqueMaster
®
spring tube
assembly gently to extend the winding
shafts out about 5" on each side. For
single spring applications, there will be
no left hand spring in the
TorqueMaster
®
spring tube assembly.
Lift the TorqueMaster
®
spring tube
assembly and rest it on the top of the
flagangles.
NOTE: Cable drums are marked right
and left hand. Cable drums and
TorqueMaster
®
spring tube assembly
are cam shaped to fit together only one
way.
Pre-wrap the TorqueMaster
®
plus cable
drum with the counter balance cable
with 1/2 or 1-1/2 wraps (see
illustration)
To install the cable drum, slide the
correct cable drum over the winding
shaft until the cable drum seats against
the TorqueMaster
®
spring tube
assembly.
The winding shaft must extend past the
cable drum far enough to expose the
splines and the groove. Align the
winding shaft groove with the round
notch in the flagangle.
For double spring applications:
Repeat for opposite side.
For single spring applications: Insert
the loose winding shaft into the left
hand cable drum prior to sliding the
cable drum over the TorqueMaster
®
spring tube assembly.
NOTE: On single spring applications,
take care in handling the loose winding
shaft (left side) so that it does not slide
back into the TorqueMaster
®
spring
tube assembly.
Cable Drums
Tape Measure
WINDING
SHAFT
5”
TORQUEMASTER
®
SPRING TUBE ASSEMBLY
Cable
Drum
No
space
betwee
n R
atchet
Paw
l a
nd Cable Drum
ind
icate
s engagement
Cable D
rum
Ratch
et Pawl
ENG
AGE
D SIDE
VIEW
No
space
betwee
n
Rat
chet Pawl
and
Cable Drum
ENGAG
ED UNDE
R
NE
A
T
H VIEW
Space
between Ratchet Pawl
and Cable D
rum
non-indic
ates engage
men
t
Cable Drum
Ratch
et Pawl
DISE
NGAGED S
IDE V
IEW
No space between
Rat
chet Pawl
and
DISE
NGAGED U
NDERNE
A
TH VIEW
UPPER
POS
ITION
LOWER
POS
ITION
LOWER P
OSITION SI
DE VIEW
UPPE
R POS
ITION SIDE VIEW
Ratch
et Pawl in Lowe
r P
osition
Ratch
et Pawl in Upper Posit
ion
Use
the
se Illustration,
in co
njunction w
ith the Instruct
ions
on the other side of
this l
abel.
WA RNING
Rachet Br
acket is
under
EXTREM
E SPRING
TEN
SION
.
To avoid possible
severe or
fatal injur
y,
DO NOT
re
move
fasteners
from rat
chet
bracket
until spr
ing(
s) a
re full
y
wnwo
und.
To saf
ely
unwi
nd spring(s)
read
and fol
low t
he directio
ns in the
inst
allati
on instructions/owners
manual.
DO NOT RE
MOVE THIS TAG
.
WINDING SHAFT
CABLE
DRUM
GROOVE
ROUND NOTCH
FLAGANGLE
SPLINES
COUNTERBALANCE CABLE
GROOVE
CABLE
DRUM
SPLINES
WINDING SHAFT
Right Drum
TorqueMaster
®
Spring Tube
Assembly
Right Drum
TorqueMaster
®
Spring Tube
Assembly
1/2 Wrap Shown
1-1/2 Wrap Shown
Counterbalance Cable
Counterbalance Cable