Superior SDV35 Indoor Fireplace User Manual


 
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
28
REFERENCE
Firebox Accessories / Parts
Cat. No. Model No. Description
88L53 FGE Bag of Glowing Embers
80L42 FDVS
Bag of Decorative
Volcanic Stone
Table 9
Glowing Embers
Bag of Glowing
Embers (rockwool)
Separate into Quarter
Size (separate) Pieces
NOTE: Turn off all electricity to the appliance
before you install volcanic stone, embers and
logs.
1. Remove the front glass enclosure panel
(see Removing Glass Enclosure Panels on
Page 30).
2. Locate log set, embers and volcanic stone.
Handle logs carefully to prevent break-
age.
3. Install Decorative Volcanic Stone - Mound
up a portion of the volcanic stone in front
of the burner in a pleasing pattern.
4. Placement of Glowing Embers -
Separate the Embers (rockwool) into pieces
about the size of a quarter (see Figure 53).
Keep the pieces fluffed up, not matted.
Distribute these pieces over the surface of
the burner, as shown in Figure 54. Do not
use more than is necessary. Ensure that the
main burner slots remain uncovered by the
ember material.
Note: This appliance is provided with enough
Glowing Embers for several applications, do
not use all that is in a new bag at one time.
For best glowing effect, replace the ember
material annually.
5. Placement of Logs -
The logs have locating notches or slots to
help ensure that they are properly posi-
tioned. Proper log placement is critical to
prevent sooting.
Figure 53
INSTALLATION PROCEDURE
Carefully position the ceramic fiber logs into the
firebox as shown in Figure 54. Logs should
be placed in the order shown and per the fol-
lowing instructions.
1. Place embers on the front burner tube and
volcanic stone in front of the burner as
shown and per instructions on Page 29 (see
Placement of Glowing Embers and Install
Decorative Volcanic Stone on this page).
2. Place the rear log (A) as shown. Position
the 2 notches on the bottom of log (A) over
the 2 corresponding locating brackets as
shown.
3. Place the center log (C) as shown. The 2
notches on the bottom of log (C) fit over
the corresponding locating brackets.
4. Place the left log (B) as shown. The top fork
on log (B) fits into the notch on log (A). The
bottom of log (B) rests on the sub-floor.
5. Place the top right log (D) as shown. The top
fork on log (D) fits into notch on log (A) as
shown. The bottom fork on log (D) rests on
sub-floor flange (identified in photo #1).
WARNING
DO NOT attempt to install the
logs until the appliance instal-
lation has been completed, the
gas line connected and tested
for leaks and the initial burner
operation has been checked
out.
The size and position of the log
set was engineered to give the
appliance a safe, reliable and
attractive flame pattern. Any
attempt to use a different log
set in the fireplace will void
the warranty and will result in
incomplete combustion, soot-
ing, and poor flame quality.
Logs get very hot and will
remain hot up to one hour
after gas supply is turned off.
Handle only when logs are
cool. Turn off all electricity
to the appliance before you
install grate, volcanic stone,
vermiculite, embers and
logs.
This appliance is not designed
to burn wood. Any attempt
to do so could cause irrepa-
rable damage to the appliance
and prove hazardous to your
safety.
If logs are not installed
according to the log instal-
lation instructions, flame
impingement and improper
combustion could occur and
result in soot and/or excessive
production of carbon monoxide
(CO), a colorless, odorless,
toxic gas.
Step 7. INSTALL VOLCANIC STONE,
GLOWING EMBERS AND LOGS