Filter
Top Products
13369-1-0203 Page 27
PIEZO IGNITOR
PIEZO IGNITOR
VALVE CONTROL KNOB
VALVE CONTROL KNOB
VARIABLE REGULATOR
VARIABLE REGULATOR
("HI"-"LO") KNOB
("HI"-"LO") KNOB
REMOTE/ON/OFF SWITCH
REMOTE/ON/OFF SWITCH
DOOR ASSEMBLY (SHOWN OPEN)
DOOR ASSEMBLY (SHOWN OPEN)
GAS VALVE
GAS VALVE
Figure 49
Initial Lighting
Upon completing the gas line or turning the gas valve on after it
has been in the "OFF" position, a small amount of air will be in
the lines. When first lighting the fireplace, it will take a few
minutes for the lines to purge themselves of this air. Once the
purging is complete, the fireplace will light and operate
satisfactorily.
Subsequent lightings of the appliance will not require such
purging if the gas valve is not turned to "OFF."
Pilot Flame (Figure 50)
The thermopile/thermocouple (standing pilot) tips should be
covered with flame.
Figure 50
STANDING PILOT OPERATING INSTRUCTIONS
ON/OFF/REMOTE Switch
DVS is equipped with an ON/OFF/REMOTE switch. A wire
harness is attached to the ON/OFF/REMOTE switch. The red,
black and green (wires) female push-ons attach to the ON/OFF/
REMOTE switch. At the opposite end of the wire harness, the
black and green (wires) female push-ons attach to the gas valve.
An additional green wire and the red wire, which are stripped and
bare, will attach to the 750 millivolt wall thermostat accessory,
or, to one of the other accessories that can be purchased for use
with your log set.
Operation of ON/OFF/REMOTE Switch with no Accessories
To ignite main burner, turn the control knob on the gas valve from
the PILOT position to the ON position. Turn the ON/OFF/
REMOTE switch from the OFF position to the ON position. The
additional green wire and red wire, which are stripped and bare
are not used.
Operation of ON/OFF/REMOTE Switch with Accessories
750 Millivolt Wall Thermostat, GWSG-T
Connect the green and red, stripped and bare, wires on the ON/
OFF/REMOTE switch wire harness to the wall thermostat. Turn
the ON/OFF/REMOTE switch to the REMOTE position. Set the
wall thermostat to the desired temperature.
It is important to use wire of a gauge proper for the length of the
wire:
RECOMMENDED WIRE GAUGES
Maximum Wire
Length Gauge
1' to 10' 18
10' to 25' 16
25' to 35' 14
Wall Switch, FWS-1
Connect the green and red, stripped and bare, wires on the ON/
OFF/REMOTE switch wire harness to the wall switch. Turn the
ON/OFF/REMOTE switch to the REMOTE position. Pivot the
rocker switch on the FWS-1 to the ON position.
Battery Operated Remote Control, FRBC-1 and FRBTC-1
Connect the green and red, stripped and bare, wires on the ON/
OFF/REMOTE switch wire harness to the remote receiver that is
a component in the FRBC-1 and FRBTC-1. Turn the ON/OFF/
REMOTE switch to the REMOTE position. Follow instructions
in the FRBC-1 and FRBTC-1 to complete installation.
Note: If batteries fail in FRBC-1 or FRBTC-1, and immediate
heat is desired, turn the ON/OFF/REMOTE switch from the
REMOTE position to the ON position.
Electric (120 volt) Operated Remote Control, FREC-1
Connect the green and red, stripped and bare, wires on the ON/
OFF/REMOTE switch wire harness to the wires on remote
receiver that is a component in the FREC-1. Turn the ON/OFF/
REMOTE switch to the REMOTE position. Follow instructions
in the FREC-1 to complete installation.
Note: If electric (120 volt) fails in FREC-1, and immediate heat
is desired, turn the ON/OFF/REMOTE switch from the REMOTE
position to the ON position.
Wiring of ON/OFF/REMOTE Switch with 750 Millivolt Wall
Thermostat Accessory and Another Accessory
Connect the green and red, stripped and bare, wires on the ON/
OFF/REMOTE switch wire harness to the 750 millivolt wall
thermostat AND to the remote receiver that is a component in the
FRBC-1, FREC-1 OR to the FWS-1, wall switch.
1. Connect (1) wire from the 750 millivolt wall thermostat and (1)
wire from appropriate accessory to the GREEN, stripped and
bare wire from the ON/OFF/REMOTE wire harness.
2. Connect (1) wire from the 750 millivolt wall thermostat and (1)
wire from appropriate accessory to the RED, stripped and bare
wire from the ON/OFF/REMOTE wire harness.
Note: When the appliance is in the MANUAL mode and the
batteries fail in the FRBC-1 or if the electric (120 volt) fails in
the FREC-1, and immediate heat is desired, turn the ON/OFF/
REMOTE switch from the REMOTE position to the ON
position.