Filter
Top Products
Commercial Lighting Design Guide Wall Box Dimmers and Switches
Doc 4775A 74
Cresnet Wall Box Switches
Model Load Features
CLW-SW
Wall Box
Switch
(Stand-alone)
Supports incandescent and
electronic low voltage loads
up to 1000 watts, or
magnetic low-voltage and
neon/cold cathode loads
up to 1000VA/750 watts.
Fluorescent ballasts, high-
intensity discharge lighting,
and ceiling fans can also
be switched.
Large button provides instant on/off control of the load,
while the small button turns the load off following a preset
time delay. The slide switch selects between ADJUST,
PRESET, and OFF modes. PRESET mode is the normal
operating mode, and ADJUST mode is used for setting
the delay time.
NOTE: The wall box switches do not support fan speed
control. Use the CLX-1FAN4 for fan speed control.
CLW-SW1
Wall Box
Switch, Single
Button
(Stand-alone)
Supports incandescent and
electronic low voltage loads
up to 1000 watts, or
magnetic low voltage and
neon/cold cathode loads
up to 1000VA/750 watts.
Fluorescent ballasts, high-
intensity discharge lighting,
and ceiling fans can also
be switched.
Provides instant turn-on control of the load. Pressing the
button again turns the load off following a preset time
delay. The time delay can be overridden by tapping the
button a second time, turning the load off instantly. The
slide switch on the CLW-SW1 selects ADJUST, PRESET,
and OFF modes. PRESET mode is the normal operating
mode, and ADJUST mode is used for setting the delay
time.
CLW-SWS1
Wall Box
Master Switch,
Single Button
(Master)
Supports incandescent and
electronic low voltage loads
up to 1000 watts, or
magnetic low voltage and
neon/cold cathode loads
up to 1000VA/750 watts.
Fluorescent ballasts, high-
intensity discharge lighting,
and ceiling fans can also
be switched
Multiple units may be ganged side-by-side along with
other CLW-Series switches and dimmers or non-Crestron
devices. The single large button on the CLW-SWS1
provides instant turn-on control of the load. Pressing the
button again turns the load off following a preset time
delay. The time delay can be overridden by tapping the
button a second time, turning the load off instantly. The
slide switch on the CLW-SWS1 selects ADJUST, PRESET,
and OFF modes. PRESET mode is the normal operating
mode, and ADJUST mode is used for setting the delay
time.
CLW-SLVS1
Wall Box Slave
Switch, Single
Button
(Slave)
Supports incandescent and
electronic low voltage loads
up to 1000 watts, or
magnetic low-voltage and
neon/cold cathode loads
up to 1000VA/750 watts.
One-gang wall mount slave switch designed for use
with the CLW-SWS1 Wall Box Master Switch to provide
multipoint switching control of a single load. The single
pushbutton on the CLW-SLVS1 provides parallel
functionality to that on the CLW-SWS1.
CLW-SWS
Wall Box
Master Switch
(Master)
1000 watt electronic light
switch designed to mount in
a standard electrical gang
box
Serves as the master for multipoint switching control of a
single load. Multi-point switching functionality (similar to
3-way or 4-way switching) is enabled by using the CLW-
SWS with one or more CLW-SLVS Slave Switches. The
large button on the CLW-SWS allows for instant on/off
control of the load, the small button turns the load off
following a preset time delay. The slide switch selects
between ADJUST, PRESET, and OFF modes. PRESET mode
is the normal operating mode, and ADJUST mode is used
for setting the delay time.
NOTE: The wall box switches do not support fan speed
control. Use the CLX-1FAN4 for fan speed control.
CLW-SLVS
Wall Box Slave
Switch
(Multipoint
Slave)
1000-Watt electronic light
switch designed to mount in
a standard electrical gang
box
One-gang wall mount slave switch designed for use
with the CLW-SWS Wall Box Master Switch to provide
multipoint switching control of a single load. The
pushbuttons on the CLW-SLVS provide parallel
functionality to those on the CLW-SWS.
NOTE: In systems, only the master unit is connected to Cresnet®. Slave units are connected by the120V
(Traveler) wire.