Filter
Top Products
are properly protected against moisture or other contaminants. Wood doors, in a non-finished
condition, must not be transported or stored where the wood surfaces can be exposed to
moisture or other contaminants.
Wood (Surface Preparation)
All surfaces must be clean, free of dust and dirt and any other contamination.
Wood (Painting)
Using painter’s tape, tape off all metal surfaces. A premium quality latex house based finish
paint is recommended for use over the factory latex based primer
Painting the wood surfaces with at least 2 coats of finish paint over the primer. Follow paint
manufacture’s label directions completely for all coatings. Once finished, remove painter’s
tape and touch up where necessary.
Wood (Maintenance and Refinishing)
Yearly inspection of all the wood surfaces of the garage door(s) will reveal the extent of
weathering and the need for refinishing. When the finish becomes eroded or thin, clean
and prime the areas of deterioration. Follow up with a complete refinishing of the door(s),
according to the above directions, as well as the manufacturer’s label directions. Protecting
the door(s) from prolonged exposure to moisture and sunlight is vital in extending the service
life of your garage door(s).
Operation And Maintenance
OPERATING YOUR GARAGE DOOR:
Before you begin, read all warning labels affixed to the door and the installation instructions
and owner’s manual. When correctly installed, your Wayne-Dalton door will operate smoothly.
Always operate your door with controlled movements. Do not slam your door or throw your
door into the open position, this may cause damage to the door or its components. If your
door has an electric opener, refer to the owner’s manual to disconnect the opener before
performing manual door operation below.
Manual door operation:
For additional information on manual garage door operations go to www.dasma.com and
reference TDS 165.
IMPORTANT: DO NOT PLACE FINGERS OR HANDS INTO SECTION JOINTS WHEN OPENING
AND/OR CLOSING A DOOR. ALWAYS USE LIFT HANDLES / SUITABLE GRIPPING POINTS
WHEN OPERATING THE DOOR MANUALLY.
Opening a Door: Make sure the lock(s) are in the unlocked position. Lift the door by using the
lift handles / suitable gripping points only. Door should open with little resistance.
Closing a Door: From inside the garage, pull door downward using lift handles / gripping point
only or a high friction area only. If you are unable to reach the lift handles/ suitable gripping
points only, use pull down rope affixed to the side of door. Door should close completely with
little resistance.
Using an electric operator:
IMPORTANT: PULL DOWN ROPES MUST BE REMOVED AND LOCKS MUST BE REMOVED OR
MADE INOPERATIVE IN THE UNLOCKED POSITION.
When connecting a drawbar (trolley type) garage door operator to this door, an drawbar
opener and/or drawbar operator bracket must be securely attached to the top section of the
door, along with any struts provided with the door. Always use the drawbar operator and or
drawbar operator bracket supplied with the door. To avoid possible damage to your door,
Wayne-Dalton recommends reinforcing the top section on models 8000, 8100, 8200 and
9100 doors with a u-bar (may or may not be supplied). The installation of the drawbar opera-
tor must be according to manufacturer’s instructions and force settings must be adjusted
properly. Refer to the owner’s manual supplied with your drawbar operator for complete
details on installation, operation, maintenance and testing of the operator.
Maintaining Your Garage Door:
Before you begin, read all warning labels affixed to the door and the installation instruc-
tions and owner’s manual. Perform routine maintenance steps once a month, and have the
door professionally inspected once a year. Review your Installation Instructions and Owner’s
Manual for the garage door. These instructions are available at no charge from Wayne-Dalton,
A Division Of Overhead Door Corporation, P.O. Box 67, Mt. Hope, OH., 44660, or at www.
wayne-dalton.com. For additional information on garage door/operator maintenance go to
www.dasma.com and reference TDS 151, 167 and 179.
Monthly Inspections:
1. Visual Inspection: Closely inspect jambs, header and mounting surface. Any wood found
not to be structurally sound must be replaced. Inspect the springs, counterbalance lift cables,
track rollers, pulleys, rear back hangs and other door hardware for signs of worn or broken
parts. Tighten any loose screws and/or bolts. Check exterior surface of the door sections
for any minor cracks. Verify door has not shifted right or left in the opening. If you suspect
problems, have a trained door system technician make the repairs.
WARNINGWARNING
GARAGE DOOR SPRINGS, COUNTERBALANCE LIFT CABLES, BRACK-
ETS, AND OTHER HARDWARE ATTACHED TO THE SPRINGS ARE UNDER
EXTREME TENSION, AND IF HANDLED IMPROPERLY, CAN CAUSE SEVERE
OR FATAL INJURY. ONLY A TRAINED DOOR SYSTEMS TECHNICIAN
SHOULD ADJUST THEM, BY CAREFULLY FOLLOWING THE MANUFAC-
TURER’S INSTRUCTIONS.
WARNINGWARNING
NEVER REMOVE, ADJUST, OR LOOSEN THE BOLTS, SCREWS AND/OR
LAG SCREWS ON THE COUNTERBALANCE (END OR CENTER BEARING
BRACKETS) SYSTEM OR BOTTOM CORNER BRACKETS OF THE DOOR.
THESE BRACKETS ARE CONNECTED TO THE SPRING(S) AND ARE UNDER
EXTREME TENSION. TO AVOID POSSIBLE SEVERE OR FATAL INJURY,
HAVE ANY SUCH WORK PERFORMED BY A TRAINED DOOR SYSTEMS
TECHNICIAN USING PROPER TOOLS AND INSTRUCTIONS.
TorqueMaster
®
Plus Springs: Pawl knob(s) (located on the TorqueMaster
®
end brackets above
the door) should be engaged to prevent the door from rapidly descending in case of spring
failure or forceful manual operation.
Torsion Springs: The torsion springs (located above the door) should only be adjusted by a
trained door systems technician. DO NOT attempt to repair or adjust torsion springs yourself.
Extension Springs: A restraining cable or other device should be installed on the extension
spring (located above the horizontal tracks) to help contain the spring if it breaks.
2. Door Balance: Periodically test the balance of your door. If you have a garage door
drawbar operator, use the release mechanism so you can operate the door by hand when do-
ing this test. Start with the door in the fully closed position. Lift the door to check its balance.
Adjust TorqueMaster
®
or Extension spring(s), if door lifts by itself (hard to pull down) or if
door is difficult to lift (easy to pull down). DO NOT attempt to repair or adjust Torsion Springs
yourself. To adjust TorqueMaster
®
or Extension spring(s), refer to your installation instructions
and owner’s manual. If in question about any of the procedures, do not perform the work.
Instead, have it adjusted by a trained door systems technician.
3. Lubrication: The door should open and close smoothly. Ensure the door track rollers
are rotating freely when opening and closing the door. If track rollers do not rotate freely,
clean the door tracks, removing dirt and any foreign substances. Clean and lubricate (use
a non-silicon based lubricant) graduated end hinges, center hinge(s), steel track rollers,
bearings and torsion spring(s) (torsion spring coil surfaces). DO NOT lubricate plastic idler
bearings, nylon track rollers, door track. DO NOT oil a cylinder lock, if actuation is difficult use
a graphite dust to lubricate.
20