Filter
Top Products
5/16”-18 x 3/4”
Carriage bolt
(4) 1/4”-20 x 11/16”
Self drilling screws
Top fixture
base
Top fixture
slide
5/16”-18
Hex nut
End
cap
Top section
Short stem
track roller
Top Section
Tools Required: Hammer, Step ladder, Tape measure
15
Place the top section in the opening. Temporarily secure the top section by driving a nail in
the header near the center of the door and bending it over the top section. Now, flip up the
hinge leaves, hold tight against section, and fasten center hinges first and end hinges last
(refer to step, Stacking Sections). Vertical track alignment is critical. Position flag angle or wall
angle between 1-11/16” (43 mm) to 1-3/4” (44 mm) from the edge of the door; tighten the
bottom lag screw. Flag angles or wall angles must be parallel to the door sections. Repeat for
other side.
IMPORTANT: THE DIMENSION BETWEEN THE FLAG ANGLES OR WALL ANGLES MUST BE
DOOR WIDTH PLUS 3-3/8” (86MM) TO 3-1/2” (89 MM) FOR SMOOTH, SAFE DOOR OPERA-
TION.
FOR QUICK INSTALL TRACK: Complete the vertical track installation by securing the jamb
bracket(s) and tightening the other lag screws. Repeat for other side.
FOR FULLY ADJUSTABLE TRACK OR RIVETED TRACK: Complete the vertical track instal-
lation by securing the jamb bracket(s) and tightening the other lag screws. Push the vertical
track against the track rollers so that the track rollers are touching the deepest part of the
curved side of the track; tighten all the track bolts and nuts. Repeat for other side.
FOR ANGLE MOUNT TRACK: Complete the vertical track installation by securing the jamb
bracket(s) and or tightening the other lag screws. Push the vertical track against the track
rollers so that the track rollers are touching the deepest part of the curved side of the vertical
track, as shown. Repeat for other side.
Top section
Top
section
Nail
Door width
+ 3-3/8” to 3-1/2”
1-11/16”
to 1-3/4”
Flag
angle
Vertical track
against track rollers
Flag angle or
wallangle assembly
Top of flag angle or
Top of wallangle assembly
Operator Bracket
Tools Required: Level, Power drill, 7/16” Socket driver, Tape measure
16
IMPORTANT: WHEN CONNECTING A TROLLEY TYPE GARAGE DOOR OPENER TO THIS DOOR,
A WAYNE-DALTON OPERATOR/ TROLLEY BRACKET MUST BE SECURELY ATTACHED TO
THE TOP SECTION OF THE DOOR IF ONE HAS BEEN PROVIDED, ALONG WITH ANY U-BARS
PROVIDED WITH THE DOOR (IF A WAYNE-DALTON OPERATOR/ TROLLEY BRACKET WAS NOT
PROVIDED WITH YOUR DOOR, THAN USE THE ONE PROVIDED BY YOUR OPERATOR MANU-
FACTURER). THE INSTALLATION OF THE OPERATOR MUST BE ACCORDING TO MANUFAC-
TURER’S INSTRUCTIONS AND FORCE SETTINGS MUST BE ADJUSTED PROPERLY.
Place the bottom half inside the top half and flush against the inside surface of the top
section. Adjust both the top and bottom halves out as far apart as possible on the section
surface. Secure the bottom half and the top halves together using (4) 5/16” - 18 x 1/2” car-
riage bolts and (4) 5/16” - 18 flange hex nuts.
NOTE: Install the 5/16” - 18 x 1/2” carriage bolts and the 5/16” - 18 flange hex nuts as far
apart as possible, prior to securing both top and bottom halves together.
Now, locate the center of the top section and align the center of the holes in the adjustable
operator bracket assembly with the top section center line. Align the adjustable operator
bracket assembly vertically.
NOTE: For retro fit applications, the adjustable operator bracket must be aligned with an
existing operator.
Slide the top half of the operator bracket under the strut, keeping the operator bracket
aligned with the center line. Remove the struts screws if necessary and attach to the top
section (through strut if necessary) using (3) 1/4” - 20 x 7/8” self drilling screws.
NOTE: If your door lacks a strut on the top section, ignore the previous paragraph.
Attach the bottom half of the operator bracket to the section surface (center hinge if neces-
sary) using (2) 1/4” - 20 x 11/16” self drilling screws.
NOTE: When attaching operator bracket to top section with strut, apply additional pressure to
thread into the strut.
(3) 1/4”- 20 x 7/8”
Self-drilling screws
(4) 5/16”- 18 x 1/2”
Carriage bolts and
(4) 5/16”- 18 flange
hex nuts
(2) 1/4”- 20 x 11/16”
Self-drilling screws
Lower half
Upper half
Strut
Drawbar
operator bracket
Center hinge
Horizontal Tracks
Tools Required: Ratchet wrench, 9/16” Socket, 9/16” Wrench, level, Step ladder
17
NOTE: Depending on your door, you may have Quick Install Flag Angles, Fully Adjustable
Flag Angles, Riveted Vertical Track Assemblies or you may have Angle Mount Vertical Track
Assemblies. Refer to Package Contents / Parts Breakdown, to determine which Flag Angles /
Vertical Track Assemblies you have.
WARNINGWARNING
DO NOT RAISE DOOR UNTIL HORIZONTAL TRACKS ARE SECURED AT
REAR, AS OUTLINED IN STEP, REAR BACK HANGS, OR DOOR COULD FALL
FROM OVERHEAD POSITION CAUSING SEVERE OR FATAL INJURY.
IF YOU HAVE QUICK INSTALL FLAG ANGLES: To install horizontal track, place the curved
end over the top track roller of the top section. Align key slot of the horizontal track with the
Quick Install tab of the flag angle. Push curved portion of horizontal track down to lock in
place.
Horizontal
track
Flag angle
Quick
Install tab
Key slot
Quick
Install tab
in place
Tracks flush
3/8”-16
Hex nut
Horizontal track
angle
3/8”-16 x 3/4”
Truss head bolt
Flag angle
IF YOU HAVE FULLY ADJUSTABLE FLAG ANGLES: To install horizontal track, place the
curved end over the top track roller of the top section. Align the bottom of the horizontal
track with the top of the vertical track. If you have Quick Install horizontal track, tighten the
horizontal track to the flag angle with a stud plate and (2) 1/4” - 20 flange hex nuts. If you
have Universal horizontal track, tighten the horizontal track to the flag angle with (2) 1/4” - 20
x 9/16” track bolts and (2) 1/4” - 20 flange hex nuts.
3/8”-16
Hex nut
Horizontal
track angle
3/8”-16 x 3/4”
Truss head bolt
Quick Install
horizontal
track
1/4”-20
Flange hex nuts
Stud
plate
Flag angle
upper slot
1/4”-20 x 9/16”
Track bolts
1/4”-20
Flange hex nuts
Fully Adjustable
horizontal track
Flag angle
upper slot
IF YOU HAVE RIVETED TRACK ASSEMBLIES OR ANGLE MOUNT VERTICAL TRACK
ASSEMBLIES: To install horizontal track, place the curved end over the top roller of the top
11