Filter
Top Products
16 Pelco Manual C1968M-A (1/02)
TECHNICAL SPECIFICATIONS
ELECTRICAL
Monitor
Input Voltage: 100 to 240 VAC, 50/60 Hz
Power Consumption: 70 watts
Signal Format: NTSC
Scanning System: 2:1 interlace
Picture Elements: 512 (H) x 492 (V)
Horizontal Resolution: 350 TV lines (center)
Linearity: Less than 12%
Audio Output: 1.1 W +/-0.2 W at 8-ohm resistive load
Pixel Format
Single Screen: 720 (H) x 480 (V)
Quad Screen: 360 (H) x 240 (V)
PIP Screen: 208 (H) x 136 (V)
Refresh Rate: 30 frames per second (NTSC)
Digital Zoom: 2X
OSD Character: 16 x 20 bit map font (upper case alpha
characters, numbers, and symbols)
Video Switching
Time When Multiple
Alarms Occur: 1 second
Maximum Character
Display Format: 45 (H) x 24 (V) (1,080 characters)
Camera
Input Voltage: 12 VDC, +/-2 VDC
Power Consumption: 2 watts
Signal Format: NTSC
Scanning System: 2:1 interlace
Sync System: Internal
Horizontal Resolution: 330 TV lines (center)
Image Size Area: 4.57 mm (H) x 3.90 mm (V)
Picture Elements: 512 (H) x 492 (V)
Electronic Iris: 1/60 to 1/100,000 second
Video Output: 1.0 Vp-p, +/-10%, 75 ohms
Auto White Bal.: Electronic auto tracking
Minimum Illumination: 0.9 lux at 30 IRE, f1.2
GENERAL
Monitor
Picture Tube: 14-inch diagonal color
Controls: Sharpness, color, brightness, contrast,
tint, and volume
Character Display: 8 alphanumeric characters each for
camera, date, time, alarm, video loss,
and freeze for each channel
Display Modes: One camera, four cameras (quad),
picture-in-picture (PIP), and VCR
Sequential
Switching Mode: Set dwell time from 1 to 30 seconds;
OFF setting skips channel
Video Loss
Detection: All channels
Time Mode: 12-hour mode with AM/PM indicator
Alarm Inputs: 4, activated by N.O. or N.C. contact
closure (programmable)
Alarm Output: 1, common to all 4 inputs, TTL compat-
ible (programmable for high or low out-
put)
Alarm Beep: On or off (programmable)
Automatic
Alarm Reset: Set reset time from 1 to 60 seconds;
OFF setting defeats auto reset
(programmable)
Video/Audio
Input Connectors: 4X6P mini-DIN
Video Input
Connectors: 4 BNC
Video Looping
Connectors: 4 BNC
Monitor Output
Connector: 1 BNC
VCR Input/Output
Connectors: 4 RCA (2 video and 2 audio)
Remote Port
Connector: DB9 male
Alarm Connector: 10-position, snap-in type (push-in wire
Impedance
Ter mination: 75 ohms or bridging for 4 video inputs
(from cameras) and 1 monitor output
Dimensions: 13.68 (W) x 12.75 (H) x 14.68 (D) inches
(34.75 x 32.38 x 37.29 cm)
Weight: 28.6 lb (13 kg)
Camera
Lens: C/CS mount, f2.0, 4 mm lens
Dimensions: 2.00 (W) x 4.00 (L) x 2.38 (H) inches
(5.08 x 10.16 x 6.05 cm)
Weight: 0.5 lb (0.22 kg)
ENVIRONMENTAL
Monitor
Operating
Temperature: 32° to 104°F (0° to 40°C)
Storage
Temperature: 4° to 158°F (-20° to 70°C)
Humidity: 35% to 80%, non-condensing
Camera
Operating
Temperature: 14° to 131°F (-10° to 55°C)
Storage
Temperature: 4° to 158°F (-20°to 70°C)
Humidity 35% to 80%, non-condensing
(Design and product specifications subject to change without
notice.)