Freedom F-64 Installation Instructions
L NAPCO Security Systems
WI1501A 9/06
Page 28
Number of Rings Before Pickup (Answer on Ring) See Callback-Method Download
One-Button Arming See Easy Arming
Opening Report; Opening Report Only After Alarm Report (Do not program for UL installations).
Opening and closing reports are generally used in commercial installations. On disarming, the communicator can send an Opening
Code for Users 1–64 (Opening Report), or it may transmit only when the control panel is disarmed after an alarm has been reported
(Opening Report Only After Alarm Report). (Note: Keyfobs 1–8 report as Users 57–64). Subscriber Identification Numbers and
Opening Codes must be entered for either opening report.
Program Opening Report Only After Alarm Report to report only when disarming after an alarm report. This feature may be used by the
central station to verify that the subscriber has responded and disarmed the panel. If "Opening Report Only After Alarm Report" is
selected, also select "Opening Report" for each user.
Panics; Aux Panic; (Police) Panic; Fire Panic See Fire; Remote Panic
The Panic Zone is always a 24-Hour Zone. Each Freedom Touchpad possesses a Fire, Auxiliary and Police Panic button. To activate
at a Touchpad, a Panic button must be Held Down for 2 seconds to activate the emergency alarm and transmit the signals to cen-
tral station. For keypads installed in the system, each keypad is individually selectable for keypad panics (see Keypad Features). If
"Keypad Panic" is programmed for a keypad, police panic is activated by simultaneously pressing the
9 and G buttons. If
"Keypad Aux." is programmed, pressing the 8 and G buttons simultaneously will trip an auxiliary emergency alarm. If
"Keypad Fire" is programmed, pressing the
7 and G buttons at the same time will activate fire panic.
Perimeter Group Bypass
A new byzone feature has been created to allow bypassing of all faulted perimeter zones excluding the initiating Touchpad primary door.
This feature should be set for all NON-STAY, NON-24HOUR and NON-NEVER ARM zones in an area. Note: Without this feature pro-
grammed on all perimeter zones, the Touchpad command "Bypass All Faulted Zones" will not function correctly. When the Easy Menu
Driven Program Mode menu is used, the non-STAY, non-Fire, non-24H and NON-NEVER ARM zones are properly programmed for this
feature.
Power-Up Delay
If programmed, power-up will be delayed for 5 minutes to allow devices such as PIRs time to stabilize (warm up). This will prevent false
alarms when ac power is restored after a long power outage and the backup battery is discharged. SIA CP-01 requires you must pro-
gram this feature on all zones with sensors.
Pre-Alarm Warning (Not for UL installations)
Programmable by zone, this feature will cause an alarm to sound only at the Touchpad for the duration of the programmed Abort Delay
(see Abort Delay; Time Selection). After the delay has elapsed, the alarm output will activate and a report will be sent. On a system
containing both interior and perimeter zones, the Pre-Alarm Warning will be active ONLY while the system is armed Stay (interior zones
bypassed). Tripping the perimeter zones activates an audible Touchpad warning before the alarm. If armed Away, ALL pre-Alarm warn-
ing zones will cause an immediate alarm if tripped. Entry/Exit zones should not have Pre-Alarm Warning programmed. On systems with
perimeter zones only, the pre-alarm warning will always be active when the system is armed. To enable, select Pre-Alarm Warning in
Zone features and provide an Abort Delay Time of 0 to 254 seconds. Zero defaults to 10 seconds.
Pre-Dial Delay
A Pre-Dial Delay may be used whenever a delay is required before dialing. It may be required when programming Dial-Tone Detection,
which causes the communicator to wait before it attempts to detect a dial tone (see Dial-Tone Detection). Certain telephone exchanges
send a nonstandard dial tone that the communicator may not be able to detect. With these nonstandard exchanges, it is possible to
program Pre-Dial Delay rather than Dial-Tone Detection. This will cause the communicator to wait for a 4 second time period before
dialing.Contact the telephone-equipment supplier to find out how long a delay is required before dialing. Select "Pre-Dial Delay" by
programming one "D" for each 4-second delay required immediately before the telephone number. In UL installations, do not program
more than one "D" before the telephone number. See Backup Report on Telco 2; Report Telco 3 (Double or Split Reporting). Also see
Access Number for Outside Line; Telephone Numbers.
Print Module Support
The bus mounted GEM-PRINT will print all system activity. If the GEM-PRINT fails, it will cause an E27- 00 Printer Fail system trouble.
Priority Area Arming
Prevents area arming if the alternate Priority Area has not yet been armed.
Priority Zone (Required for all zones in UL installations)
A zone that will prevent arming if faulted. If an attempt is made to arm, the sounder will come on and a warning message will be
displayed indicating that the system cannot be armed. The Touchpad may be reset by simply pressing the RESET button. The fault on
Glossary