Filter
Top Products
23
MAN-0076 Rev 05 Millennium II
December 07, 2012
Net Safety Monitoring Inc
Figure 17: Menu structure flow chart
Serial number &
Firmware
version............
(Navigate with 1 & 2, select
with menu button 3. See page
34).
Ch1:050
Ch2:050
Exit
(Navigate with 1 & 2, select
with menu button 3. See page
34).
Ch1: ‘target gas’
Ch2: ‘target gas’
Exit
(Navigate with 1 & 2, select
with button 3. See page 34).
Ch1: range
Ch2: range
Exit
(Navigate with 1 & 2, select
with button 3. See pages 33 &
34).
Self test relay,
caution will trip
alarm
Yes No
(Select with buttons 1 & 3.
See page 33).
Initiate reset
Yes No
(Select with buttons 1 & 2.
See page 33).
Recent events
(Navigate with 1 & 2, select
with button 3. See page 32).
Select calibration
gas value. (Activate
menu button 3 to
display sub menu)
Select gas type.
(Activate menu
button 3 to display
sub menu)
Sensor range/
scale. (Activate
menu button 3 to
display sub menu)
Self test relay.
(Activate menu
button 3 to display
sub menu)
Manual reset
(Activate menu
button 3 to display
sub menu)
View event log
(Activate menu
button 3 to display
sub menu)
Set Modbus
options (Activate
menu button 3 to
display sub menu)
Set Relay Alarm
mode (Activate
menu button 3 to
display sub menu)
Relay assignment.
(Activate menu
button 3 to display
sub menu)
Set Relay
Options (Activate
menu button 3 to
display sub menu)
Set Alarm
levels? (Activate
menu button 3 to
display sub menu)
Calibrate sensor?
Activate menu button 3 to
display sub menu)
Ch1: Enabled
CH2: Enabled
Exit
(Navigate with 1 & 2, select with
button 3. See page 27).
Year, month, day
(Navigate with 1 & 2, select with
button 3. See page 31).
Slave address
Baud rate
Parity
(Navigate with 1 & 2, select with
button 3. See page 30 & 31).
English
Exit
(Navigate with 1 & 2, select with
button 3. See page 30).
Ch1: above-above
Ch2: above-above
Exit
For O2 sensor only
(Navigate with 1 & 2, select with
button 3. See page 30).
Alarm relay 1
Alarm relay 2
Alarm relay 3
Exit
(Navigate with 1 & 2, select with
button 3. See pages 28, 29 &30).
Fault relay
Alarm relay 1
Alarm relay 2
Alarm relay 3
(Navigate with 1 & 2, select with
button 3. See page 28).
Set CH1 level
Set CH2 Level
Exit
(Navigate with 1 & 2, select with
button 3. See page 27 & 28).
Calibrate sensor 1
Calibrate sensor 2
Exit
(Navigate with 1 & 2, select with
button 3. See pages 24, 25 & 26).
Set current date
(Activate menu
button 3 to display
sub menu)
EXIT. (Activate
menu button 3 to
exit main menu)
Calibrate sensor.
(Activate menu
button 3 to display
sub menu)
Enable/disable
channels?(Activat
e menu button 3 to
display sub menu
Activate button 1
Activate button 2
Activate button 1
Activate button 2
Activate button 1
Activate button 2
Activate button 1
Activate button 2
Activate button 1
Activate button 2
Activate button 1
Activate button 2
Activate button 1
Activate button 2
Activate button 1
Activate button 2
Activate button 1
Activate button 2
Activate button 1
Activate button 2
Activate button 1
Activate button 2
Activate button 1
Activate button 2
Activate button 1
Activate button 2
Activate button 1
Activate button 2
Activate button 1
Activate button 2
Activate button 1
Activate button 2
Sub menu
Sub menu
Activate any menu button
then select ‘yes’ with menu
button 1 to enter main menu
Activate button 2
Activate button 1
Serial number &
firmware. (Activate
menu button 3 to
display sub menu)
Set display
language.(Activate
menu button 3 to
display sub menu)
Setup current
Time (Activate
menu button 3 to
display sub menu)
Hour, minutes
(Navigate with 1& 2, select
with button 3. See pages 31
&32).
Activate button 2
Activate button 1