Filter
Top Products
13
106442
OWNER’S MANUAL
VENTING
INSTALLATION
Continued
HIGH ALTITUDE INSTALLATION
Your Vanguard direct-vent fireplace has
been CSA/AGA tested and approved for
elevations from 0-2000 feet and CGA certi-
fied for elevations from 0-4500 feet.
When installing this fireplace at an elevation
above 2000 feet (in the USA), you may need
to decrease the input rating by changing the
existing burner orifice to a smaller size. Re-
duce input 4% for each 1000 feet above sea
level. Check with your local gas company for
proper orifice size identification.
When installing this fireplace at an eleva-
tion above 4500 feet (in Canada), check
with local authorities.
Consult your local gas company to help de-
termine the proper orifice for your location.
For assistance with any high altitude installa-
tion contact DESA International’s Technical
Service Department at 1-800-DESA-LOG
(1-800-337-2564).
PARTS LISTS FOR VENTING
KITS AND COMPONENTS
Vanguard Rigid Venting
Number Description
*MDV9K 9' Vertical Vent Kit
Includes one each: 48" Pipe, 36"
Pipe, 24" Pipe, 30° Elbow,
Firestop, Roof Flashing, Storm
Collar, Flue Restrictor Disc, and
Vertical Termination Cap
*MDVGFK
Ground Floor Horizontal Vent
Kit
(Allows horizontal installations
that run 49.5" min. vertically and 15"
horizontally from the back of the fire-
place to the outside wall.)
Includes one each: 12" Pipe,
7"-12" Adjustable Pipe, 30° Elbow,
90° Elbow, Firestop, Vinyl Stand-
off, and Horizontal Termination Cap
Number Description
*CVK Corner Vent Kit (also used for
horizontal runs)
Includes: 7" x 30º Elbow, 7" x 90º
Elbow, 7" Adjustable Galvanized
Pipe (7-12"), 6" Pipe, Wall
Thimble, Horizontal Termination,
RTV Silicone and 20 Screws
*BVK Basement Rigid Vent Kit
Includes: 7" x 30° Elbow, 7" x 4'
Galvanized Pipe, 7" x 90° Elbow, 7"
Adjustable Galvanized Pipe (7-12"),
Wall Thimble, Horizontal Termina-
tion, RTV Silicone and 20 Screws
*SVK Snorkel Rigid Vent Kit
Includes: 7" x 30° Elbow, 7" x 4'
Galvanized Pipe, 7" x 90° Elbow, 7"
Adjustable Galvanized Pipe (7-12"),
Wall Thimble, 36" Snorkel Termi-
nation, RTV Silicone and 28 Screws
*RVF Roof Rigid Vent Kit
Includes: Flue Restrictor, Storm
Collar, 7" x 30° Elbow, 7" x 4'
Galvanized Pipe, 7" x 2' Galvanized
Pipe, 7" Adjustable Galvanized Pipe
(7-12"), Firestop Support, Roof
Flashing, RTV Silicone, Vertical
Termination, and 26 screws
D1000 7" x 12" Galvanized Coaxial
Pipe (6 pcs.)
D1010 7" x 24" Galvanized Coaxial
Pipe (6 pcs.)
D1020 7" x 48" Galvanized Coaxial
Pipe (6 pcs.)
D1030 7" Adjustable (7-12")
Galvanized Coaxial Pipe (6 pcs.)
D1050 7" x 6" Galvanized Coaxial
Pipe (6 pcs.)
D2000 7" x 90° Elbow (6 pcs.)
D2010 7" x 45° Elbow (6 pcs.)
*D2060 7" x 45° Starter Elbow
D3000 Wall Strap/Offset Support (6 pcs.)
D3010 Storm Collar (6 pcs.)
D3020 Wall Thimble (6 pcs.)
D3050 Vertical Restrictor (6 pcs.)
D3060 Ceiling Firestop/Support
(6 pcs.)
D3070 Rectangular Horizontal Rigid
Vent Termination Cap
D3071 Adjustable Horizontal Rigid
Vent Termination Cap
D3090 Cathedral Ceiling Support Box
SIMPSON DURA-VENT
GS 4" x 6
5
/8 "
Number Description
902 7" x 48" Pipe
903 7" x 36" Pipe
904 7" x 24" Pipe
906 7" x 12" Pipe
907 7" x 9" Pipe
908 7" x 6" Pipe
911 7" Adjustable (11"-14
5
/8") Pipe
940 Wall Thimble
941 Cathedral Ceiling Support Box
943 Roof Flashing 0/12-6/12
943S Roof Flashing 7/12-12/12
945 7" x 45° Elbow
950 Vinyl Siding Standoff
953 Storm Collar
963 Ceiling Firestop
981 36" Snorkel Termination
984 Horizontal Termination Vent Cap
988 Wall Strap
990 7" x 90° Elbow
991 Vertical High Wind Termination
Vanguard Rigid Venting
(Cont.)
*NOTICE: The 7" x 30° Elbow sup-
plied with kits CVK, BVK, SVK,
and RVF cannot be used. IT MUST
BE REPLACED WITH A 7" X 45°
STARTER ELBOW (D2060) PUR-
CHASED SEPARATELY.
Number Description
D4000 Roof Flashing 6/12-9/12
D4010 Roof Flashing 9/12-12/12
D4020 Flex Connector (6 pcs.)
D4030 Flex Wall Thimble (6 pcs.)
D4040 4" Hose Clamp (6 pcs.)
D4050 7" Hose Clamp (6 pcs.)
D5000 Wood/Vinyl Siding Standoff
(6 pcs.)
Vanguard Flexible Venting
Number Description
FGFVK Flex Ground Floor Vent Kit
Includes: Flex Adapter, 7" x 4'
Flexible Pipe, 4" x 4' Flexible Pipe,
Wall Thimble, Horizontal Termi-
nation, (4) Spacer Springs, (2) 4"
Hose Clamps, (2) 7" Hose Clamps,
RTV Silicone, and 10 Screws
D1040 7" x 25' Coaxial Flex Pipe
with Spacer Springs
D3080 Rectangular Horizontal
Flex Termination Cap
Vanguard Rigid Venting
(Cont.)
Note:
Terminations are not designed for
installation prior to transportation.
*The D2060 45° starter elbow must be
purchased separately.