Filter
Top Products
17
106442
OWNER’S MANUAL
Continued
INSTALLATION
Continued
INSTALLING LOG SET
Open
Close
Figure 42 - Removing Glass Door
GAS SUPPLY TESTING
Note:
This section is intended as a guide for
qualified service technicians installing gas
to the appliance.
CAUTION: Do not connect
appliance before pressure test-
ing gas piping. Damage to the
gas valve may result and an un-
safe condition may be caused.
O
F
F
P
I
L
O
T
O
N
P
I
L
O
T
EA
16AI
7
TPTH TP TH
Figure 41 - Millivolt Control Valve
Pilot Gas Line - Do Not Kink
To Pilot
Burner
Pilot Adjustment Cap
ON/OFF
Knob
To Main
Burner
Conversion Screw
Outlet
Pressure
Inlet
Pressure
The gas control valve is secured underneath
the firebox with two brackets fastened to the
firebox bottom. Two pressure taps are pro-
vided on the gas control valve for a pressure
gauge connection (see Figure 41).
Before proceeding, make sure the gas con-
trol valve is in the “OFF” position. Logs
have been packaged separately to prevent
damage to glass or refractory.
1. Remove top and bottom louvers by si-
multaneously pulling both top end
spring latches towards the center of the
appliance until they are disengaged from
locating holes. Repeat for bottom end
spring latches and pull outward. Reverse
procedure to install louvers back.
A
A
B
B
C
C
D
D
E
Figure 43 - Log Set (9 Pieces)
Left
Front
Right
Back
Figure 44 - Burner and Grate (Top View)
WARNING: Improper installa-
tion, adjustment, alteration, ser-
vice, or maintenance can cause
injury or property damage. Refer
to this manual. For assistance or
additional information, consult a
qualified installer, service
agency, or gas supplier.
Left
Right
Back
Front
Figure 45 - Installing Logs “A” (Top View)
2. Remove the screen rod by sliding
spring clip on one end toward the cen-
ter. Slide rod into screen rod hole until
other end of rod is free. Remove rod.
3. To open the glass door, open the pairs
of latches located on the top and bottom
of the firebox (see Figure 42).
Note:
Use
caution when opening these latches.
4. Carefully open the door. The glass door
is mounted to the firebox with 5 screws.
5. To remove the logs from the shrink
wrap, carefully cut the plastic around
the perimeter of the log. Do not try to
remove the logs from the package with-
out first cutting the plastic.
6. Figure 43 shows the log set. Logs “A”
have the knot at the end of the log. Logs
“B” have the knot at the middle of the
log. Twigs “C” have the shape of a “Y”.
Twigs “D” have the shape of bent twigs.
Twig “E” is a straight twig which is
placed across the top of Logs “B”.
7. Figure 44 shows the top view of the
burner and grate.
8. Place logs “A” as shown in Figure 45.
9. Place logs “B” as shown in Figure 46.
Lift the end of log “A” that will be
propped up and place log “B” under it.
At the same time, the other side of log
“B” is placed over the other log “A”.
Repeat procedure for the other log “B”.
10. Take twigs “C” (shaped like a “Y”)
and place them as shown in Figure 47.
11. Take twigs “D” (bent twig) and place
them as shown in Figure 47.
12. Place twig “E” across the top of logs
“B” a shown in Figure 47.
13. When finished installing the logs, close
the glass doors while making certain that
the safety door switch is fully depressed
by the door frame before securing the
four (4) spring loaded latches.
14. Replace the louvers in reverse order with
the grilles pointing in the down position.
Left
Front
Right
Back
B
B
A
A
Figure 46 - Installing Logs “B ” (Top View)
Left
Right
Back
Front
D
C
C
D
E
Figure 47 - Installing Twigs “C, D, E ” (Top
View)