Filter
Top Products
15
*Optional.
AL — Alarm Relay Contacts
ASTAT — Aquastat
BM — Blower Motor
BMC — Blower Motor Capacitor
BR — Blower Relay
CB — Circuit Breaker
CC — Compressor Contactor
CO — Condensate Overflow Sensor
COMPR — Compressor
DTS — Discharge Temp Switch
FP1 — Water Coil Freeze Protection Sensor
FP2 — Air Coil Freeze Protection Sensor
HP — High-Pressure Switch
HWG — Hot Water Generator
JW — Jumper Wire
LOC — Loss of Charge Pressure Switch
MV — Motorized Valve
NEC — National Electric Code
LEGEND
P1 — Field Wiring Terminal Block
RVS — Reversing Valve Solenoid
TRANS — Transformer
Factory Low Voltage Wiring
Factory Line Voltage Wiring
Field Low Voltage Wiring
Field Line Voltage Wiring
Printed Circuit Trace
Optional Wiring
Relay/Contactor Coil
Thermistor
Condensate Pan
Circuit Breaker
Ground
Solenoid Coil
Relay Contacts - N.C.
Relay Contacts - N.O.
Capacitor
Temperature Switch
Low Pressure Switch
High Pressure Switch
Wire Nut
Splice Cap
LED
G
NOTES:
1. Compressor and blower motor thermally protected internally.
2. All wiring to the unit must comply with NEC and local codes.
3. Transformer is wired to 460 v (BLK/RED) lead for 460/60/3 units,
575 v (GRY) lead for 575/60/3. Transformer is energy limiting or may
have circuit breaker.
4. FP1 thermistor provides freeze protection for water. When using anti-
freeze solutions, cut JW3 jumper.
5. Check installation wiring information for specific thermostat hookup.
Refer to thermostat installation instructions for wiring to the unit.
Thermostat wiring must be “Class 1” and voltage rating equal to or
greater than unit supply voltage.
6. 24-v alarm signal shown. For dry alarm contact, cut JW4 jumper and
dry contact will be available between AL1 and AL2.
7. Transformer secondary ground via Deluxe D board standoffs and
screws to control box. (Ground available from top two standoffs as
shown.)
8. Aquastat is supplied with unit and must be wired in series with the
hot leg to the pump. Aquastat is rated for voltage up to 277 v.
9. Blower motor is factory wired for high and low speeds. No other com-
bination is available.
10. The 460-v units using an ECM (electronically commutated motor) fan
motor, modulating HWR, and/or an internal secondary pump will
require a neutral wire from the supply side in order to feed the acces-
sory with 265-v.
TABLE 1 WIRE NUMBER
Blower
Speeds
12345
Factory
HI + MED
BM(H) to
BR2(6)
BM(R) to
BR2(3)
BM(M) to
BR2(7)
Not Used
BR2(6) to
BR2(4)
HI + LOW
BM(H) to
BR2(6)
BM(R) to
BR2(3)
Not Used
BM(L) to
BR2(7)
BR2(6) to
BR2(4)
MED + LOW
BM(H) to
BR2(3)
BM(R) to
BR2(3)
BM(M) to
BR2(6)
BM(L) to
BR2(7)
BR2(2) to
BR2(4)
NOTES:
1. Status LED (GREEN) Slow Flash - Controller In - Fault Retry Mode. Fast Flash - Controller in Lock-
out Mode. Slow Flash = 1 Flash per every 2 seconds. Fast Flash = 2 Flashes per every 1 second.
2. Fault LED (RED) flashes a code representing last fault in memory. If no fault in memory code 1 is
flashed.
3. Cycles appropriate code, by cycling alarm relay in the same sequence as fault LED.
4. Alarm relay closes after 15 minutes.
5. Alarm relay cycles. Closed for 5 seconds and open for 25 seconds.
DELUXE D CONTROLLER FAULT CODES
OPERATION
STATUS LED
(GREEN)
TEST LED
(YELLOW)
FAULT LED
(RED)
ALARM
RELAY
Normal Mode ON OFF Note 2 Open
Deluxe D is Non-Functional OFF OFF OFF Open
Test Mode — ON Note 2 Cycle (Note 3)
Night Setback Flashing Code 2 — Note 2 —
Emergency Shut Down Flashing Code 3 — Note 2 —
Invalid Thermostat Inputs Flashing Code 4 — Note 2 —
No Fault in Memory ON OFF Flashing Code 1 Open
HP Fault/(Lockout) Note 1
Slow Flash/
(Fast Flash)
OFF Flashing Code 2 Open/(Closed)
LP Fault/(Lockout) Note 1
Slow Flash/
(Fast Flash)
OFF Flashing Code 3 Open/(Closed)
FP1 Fault/(Lockout) Note 1
Slow Flash/
(Fast Flash)
OFF Flashing Code 4 Open/(Closed)
FP2 Fault/(Lockout) Note 1
Slow Flash/
(Fast Flash)
OFF Flashing Code 5 Open/(Closed)
CC Fault/(Lockout) Note 1
Slow Flash/
(Fast Flash)
OFF Flashing Code 6 Open/(Closed)
Over-Under Voltage Slow Flash OFF Flashing Code 7 Open (Note 4)
Normal Mode with UPS ON OFF Flashing Code 8 Cycle (Note 5)
Swapped FP1/FP2 Lockout Fast Flash OFF Flashing Code 9 Closed
Fig. 16 — Units with Deluxe D Controller, Three-Phase (460/575 V)