Filter
Top Products
(2) Roller Spacers
(1) Step plate
(Outside)
(2) Lift handles
& spacers
(1) Step plate
(Inside)
Bottom corner brackets
(as required)
Washers
Bottom corner brackets
(as required)
Clevis pinCotter ring
(2) 1/4” - 14 x 5/8”
Tamper resistant screws
1/4”-14 x 7/8” Self
drilling screws (as required)
5/16” x 1-3/4”
Cotter pin
Cotter
pin
1/4” - 20 x 2-1/2” Carriage bolts (as required)
1/4” - 20 x 2-3/4” Carriage bolts (as required)
Cable drums RH/LH
Torsion springs RH/LH
Counterbalance lift cables
End bearing bracket RH/LH (as required)
Center bracket (as required)
Center bracket
bushing (as required)
Keys
(as required)
Center coupler
assembly (as required)
Stud Plate
(as required)
1/4”-20 x 11/16” Self
drilling screws (as required)
5/16”-18 x 3/4”
Carriage bolts (as required)
1/4”-20 x 9/16”
Track bolts (as required)
3/8”- 16 Hex nuts
(as required)
1/4”- 20 Flanged
hex nuts (as required)
1/4” - 20 Hex
nuts (lift handles)
5/16”-18 Hex
nuts (as required)
5/16”-18 Flange
hex nuts (as required)
5/16”-18 x 1/2”
Carriage
bolts (as required)
(2) 3/8”-16 x 3/4”
Truss head bolts
5/16” x 1-5/8” Tamper-resistant
hex head lag screws (as required)
3/8” - 16 x 1-1/2” Hex head bolts
(as required)
5/16” x 1 5/8” Hex head lag screws
(as required)
5/16” x 2” Tamper-resistant hex head
lag screw (as required)
Door Section Identification
Door Height Bottom
Lock
(second)
Interme-
diate I
(third)
Interme-
diate II
(fourth)
Interme-
diate III
(fifth)
Interme-
diate IV
(sixth)
Interme-
diate V
(seventh)
Top
6’0” 18” 18” 18”
N/A
18”
6’3” 21” 18” 18” 18”
6’6” 21” 18” 18” 21”
6’9” 21” 21” 21” 18”
7’0” 21” 21” 21” 21”
7’6” 18” 18” 18” 18”
N/A
18”
7’9” 21” 18” 18” 18” 21”
8’0” 21” 18” 18” 18” 21”
8’3” 21” 21” 18” 18” 21”
8’6” 21” 21” 21” 21” 18”
8’9” 21” 21” 21” 21” 21”
9’0” 18” 18” 18” 18” 18”
N/A
18”
9’3” 21” 18” 18” 18” 18” 18”
9’6” 21” 18” 18” 18” 18” 21”
9’9” 21” 21” 18” 18” 18” 21”
10’0” 21” 21” 21” 18” 18” 21”
10’3” 21” 21” 21” 21” 21” 18”
10’6” 21” 21” 21” 21” 21” 21”
10’9” 21” 18” 18” 18” 18” 18”
N/A
18”
11’0” 21” 18” 18” 18” 18” 18” 21”
11’3” 21” 21” 18” 18” 18” 18” 21”
11’6” 21” 21” 21” 18” 18” 18” 21”
11’9” 21” 21” 21” 21” 18” 18” 21”
12’0” 21” 21” 21” 21” 21” 21” 18”
12’3” 21” 21” 21” 21” 21” 21” 21”
12’6” 21” 18” 18” 18” 18” 18” 18” 21”
12’9” 21” 21” 18” 18” 18” 18” 18” 21”
13’0” 21” 21” 21” 18” 18” 18” 18” 21”
13’3” 21” 21” 21” 21” 18” 18” 18” 21”
13’6” 21” 21” 21” 21” 21” 18” 18” 21”
13’9” 21” 21” 21” 21” 21” 21” 21” 18”
14’0” 21” 21” 21” 21” 21” 21” 21” 21”
When installing your door you must use sections of the appropriate height in the right stack-
ing order. What sections heights you need to use in what order depends on the height of your
door.
NOTE: Unless your door is five sections in height, you will not receive an Intermediate II
section.
3