Filter
Top Products
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
2
TABLE OF CONTENTS
Safety Rules ......................................Page 2
Tools and Building Supplies ..............Page 2
Precautions .......................................Page 2
Introduction ......................................Page 3
Clearances/Height Requirements ......Page 3
Chimney System ...............................Page 3
Assembly Outline ..............................Page 4
Location of Fireplace .........................Page 4
Assembly Steps ................................Page 5
Preinstallation Notes .........................Page 5
Clearances ........................................Page 5
Installing the Fireplace ......................Page 5
Fireplace Specifi cations .....................Page 7
Framing Specifi cations ......................Page 7
Installing the Chimney System ..........Page 8
Ten Foot Rule Summary ....................Page 10
Special Offset Instructions ................Page 11
30° Offset through Floor/Ceiling .......Page 11
Chimney Component Calculations ....Page 11
Offset Calculations ............................Page 11
Vertical Elevation Chart ....................Page 12
Offset Elevation Chart ........................Page 13
Installing Offsets ...............................Page 14
Optional Equipment Considerations ..Page 14
Blower ...............................................Page 14
Combustion Air Kits ..........................Page 15
Gas Line Connection .........................Page 15
Cold Climate Insulation .....................Page 15
Glass Doors ......................................Page 16
Fireplace Finishes ..............................Page 16
Mantels and Trim ..............................Page 16
Hearth Extensions/Wall Shields ........Page 16
Finish Requirements .........................Page 18
Installation Components ...................Page 18
PACKAGING
The assembled wood fi replace is packaged
with:
1 - One envelope containing the literature pack-
age which consists of the homeowner's
manual, installation instructions and war-
ranty (located in the fi rebox).
2 - One Combustion Air Kit
IMPORTANT: PLEASE READ AND
UNDERSTAND THESE RULES TO
FOLLOW FOR SAFETY.
SAFETY RULES:
1. Before starting your fi replace installation,
read these installation instructions carefully
to be sure you understand them completely
and in entirety. Failure to follow them could
cause a fi replace malfunction resulting in
serious injury and/or property damage.
2. Always check your local building codes.
The installation must comply with all lo-
cal, regional, state and national codes and
regulations.
3. These fi replaces must be installed with
Security Chimneys FTF8 (8" inside diameter)
Chimney System only. These systems are
intended for use in any application where
a traditional masonry type fi replace would
apply. The chimney system must always
vent to the outside of the building.
4. To ensure a safe fi replace system and to
prevent the build-up of soot and creosote,
inspect and clean the fi replace and chimney
prior to use and periodically during the heat-
ing season.
5. Burn approved fuels only as defi ned in the
Homeowner's Care and Operation Manual.
6. DO NOT use charcoal or coal under any
circumstances.
7. NEVER use gasoline, gasoline-type lantern
fuel, kerosene, charcoal lighter fl uid, or
similar liquids to start or “freshen up” a fi re
in this fi replace. Keep any fl ammable liquids
a safe distance from the fi replace.
8. NEVER leave children unattended when there
is a fi re burning in the fi replace.
9. Always keep fl ue damper open when heat is
present in the fi replace.
10.Before servicing, allow the fi replace to cool.
Always shut off any electricity or gas to the
fi replace while working on it. This will prevent
any possible electrical shock or burns.
11.This fi replace is not intended to heat an
entire home or be used as a primary heat
source. It is designed to provide aesthetics
and limited heat to the room.
12.Always ensure an that adequate supply
of replacement combustion air from the
outside of the house is accessible to the fi re
to support normal combustion. Fireplaces
consume large volumes of air during the
normal combustion process.
• In the event the home is tightly sealed with
modern energy effi cient features, the com-
bustion air kit (provided) may not provide
all the air required to support combustion.
• The manufacturer is not responsible for any
smoking or related problems that may result
from the lack of adequate combustion air. It
is the responsibility of the builder/contractor
to ensure that adequate combustion air has
been provided for the fi replace.
13. Always ensure that the air inlet to the fi replace
is free from debris and any other obstructions
that can block the entrance of air.
14.DO NOT use a fi replace insert or any other
product not specifi ed by the manufacturer
of this Superior appliance for use with this
fi replace. All gas log sets must be operated
with the damper clamped open.
15."Smoke free” operation is not warranteed
nor are we responsible for inadequate sys-
tem draft caused by mechanical systems,
general construction conditions, inadequate
chimney heights, adverse wind conditions
and/or unusual environmental factors or
conditions beyond our control.
16.Never, under any circumstances, install a
fi replace, chimney component or any acces-
sories, that has visible or suspected physical
damage as a result of handling or transporta-
tion. These items should be inspected by your
distributor or qualifi ed factory representative
to ensure safe condition. When in doubt,
consult your distributor.
17.For additional safety considerations and
complete operating instructions, refer to
the Care and Operation Manual provided
with the fi replace.
WARNING
To avoid the risk of damaging
fi replace materials and increas-
ing the risk of fi re, do not use the
fi replace to cook or warm food.
WARNING
This fi replace has not been tested
with an unvented gas log set. To
reduce risk of fi re or injury, do
not install an unvented gas log
set into this fi replace.
TOOLS AND BUILDING SUPPLIES
NORMALLY REQUIRED
Tools Supplies
Phillips screwdriver
Hammer
Saw and/or sabersaw
Level
Measuring tape
Plumb line
Electric drill and bits
Pliers
Square
Framing materials
Wall fi nishing materials
Caulking materials
(noncombustible)
Fireplace surround and
hearth extension
materials
(noncombustible)
PRECAUTIONS
Note: These fi replace systems are not diffi cult
to install. However, in the interest of safety, it is
recommended that the installer be a qualifi ed or
certifi ed “tradesman” familiar with commonly
accepted fi replace installation and safety tech-
niques as well as prevailing local codes.
The most important areas of concern dealing
with the installation of factory-built fi replaces
are clearances to combustible materials, proper
assembly of component parts, height of the
chimney system, the proper use of accessories
supplied by the manufacturer and the techniques
employed in using fi nishing materials applied to
the wall surrounding the fi replace, hearth exten-
sions and wall shields. Each of these topics will
be covered in thorough detail throughout this
manual. Please give each your special attention
as you progress with your installation.