Stovax PR0731 Electric Heater User Manual


  Open as PDF
of 26
 
5
Turning the Linea Off
• PresstheOffbuttontoextinguishthepilot
2.3 TEMP MODE
The display shows the current room temperature.
Toincreaseordecreasethefire’soutput:
• PresstheSETbuttontoselecteithertheDAYTEMP
or the NIGHT TEMP mode by briefly pressing the
SET button
• HoldtheSETbuttonuntiltheTEMPdisplayflashesand
then let go
• SetthedesiredtemperaturewiththeUPandDOWN 
arrows. (Minimum temperature 5C, maximum 30C or
fahrenheit)
• PresstheOFFbuttontostopthedisplayflashingorwait
to return to TEMP mode.
NOTE: If you set a temperature that is beneath the
current room temperature, the fire automatically
switches to OFF.
NOTE: If you would like the Night temperature control to
turn off then decrease the temperature until [---] is
displayed.
2.4 TIMER MODE
There are two programmable settings you can make over a
24 hour period, P1 and P2
P1 + = Start Timed Setting 1
P1 + = End of Timed Setting 1
P2 + = Start Timed Setting 2
P2 + = End of Timed Setting 2
2.4.1 P1 - Program 1 for a Timed Setting
• PresstheSETbuttonuntiltheTIMERmodeisdisplayed
• HoldtheSETbutton.Thedisplaysflashesthecurrent
time for P1. While the time displayed is flashing you can
alter the hours and minutes set.
To set the time your fire first lights, change the Start Timed
Setting for P1 .
•PresstheUParrowtoalterthehour
•PresstheDOWNarrowtoaltertheminutes
in 10 minute increments
•PressSETagaintomovetotheEndofTimedSetting,
P1. The display shows the current setting for P1
This is the time your Linea first shuts down:
•PresstheUParrowtoalterthehour
•PresstheDOWNarrowtoaltertheminutes
2.4.2 P2 - Program 2 for a Timed Setting
Use the same steps outlined in 2.4.1 to change the setting
for P2.
If you have already set P1 and want to alter the setting for
P2 only:
• PresstheSETbuttonuntilTIMERmodeisdisplayed
•HoldtheSETbuttonuntil the display flashes the
current time for P1
•PresstheSETbuttonagaintoscrollpastthesettingsfor
P1 and P1
Withthetimestillflashing:
•PresstheUParrowtoalterthehour
•PresstheDOWNarrowtoaltertheminutes
Once all four times are set press the OFF button or simply
wait to complete programming.
2.5 LOW BATTERY
“BATT” is displayed on the remote when its batteries need
replacement.
2.6 SETTING THE TIME
• Simultaneouslypresstheupanddownarrowbuttons
• Presstheuparrowtosetthehourandthedownarrow
to set the minutes
• PressOFFtoreturntothemanualmodeorsimplywait
2.7 SETTING THE °C/24 HOUR OR °F/12 HOUR CLOCK
• PressOFFandthedownarrowuntilthedisplaychanges
from °C/24 hour clock to °F/12 hour clock and vice
versa.
If the remote is removed, lost or damaged, signals
transmitted to the receiver cease. Your fire will go to
standby (pilot) mode after 6 hours.
2B TOUCH PAD CONTROL
2
AR1885
• PresstheON-OFFbuttontolighttheappliance,(upto
30 seconds)
• PresstheUPbuttontoincreasetheflameheight
• PresstheDOWNbuttontodecreasetheflameheight.At
thelowestpointitgoesto‘standbymode’,(onlypilot
lit)
• PresstheON-OFFbuttontoturntheapplianceoff
USER INSTRUCTIONS
 previous next