CFM Corporation A132 Indoor Fireplace User Manual


 
3
Gas Fireplace Insert
10002964
This gas appliance should be installed by a qualified installer,
preferably NFI or WETT (Canada) certified, in accordance with
local building codes and with current CSA-B149.1 Installation
codes for Gas Burning Appliances and Equipment.
For U.S.
Installations follow local codes and/or the current National Fuel
Gas Code ANSI Z223.1/NFPA 54.
In the Commonwealth of Massachusetts, all gas fittings and
installation of this heater shall only be done by a licensed gas
fitter or licensed plumber.
FOR SAFE INSTALLATION AND OPERATION OF YOUR
GAS FIREPLACE PLEASE NOTE THE FOLLOWING:
1. This appliance gives off high temperatures and should be
located out of high traffic areas and away from furniture and
draperies.
2. Children and adults should be alerted to the hazards of the
high surface temperatures of this appliance and should stay
away to avoid burns or ignition of clothing.
3. CAUTION: Due to high glass surface temperature chil-
dren should be carefully supervised when in the same
room as fireplace.
Installation & Operating Instructions
WARNING: Check with your electronics manufacturer
before installing a television or other electronic de-
vice above this fireplace.
IMPORTANT:
PLEASE READ THE FOLLOWING CAREFULLY
It is normal for fireplaces fabricated of steel to give off some
expansion and/or contraction noises during the start up or
cool down cycle. Similar noises are found with your furnace
heat exchanger or car engine.
It is not unusual for your gas fireplace to give off some odor
the first time it is burned. This is due to the curing of the paint
and any undetected oil from the manufacturing process.
Please ensure that your room is well ventilated - open
all windows.
It is recommended that you burn your fireplace for at least six
(6) the first time you use it. If optional fan kit has been installed,
place fan in the "OFF" position during this time.
Proposition 65 Warning: Fuels used in gas, wood-
burning or oil fired appliances, and the products of
combustion of such fuels, contain chemicals known to
the State of California to cause cancer, birth defects
and other reproductive harm.
California Health & Safety Code Sec. 25249.6
Insert Applications
Before installing the gas fireplace insert consideration
must be given to the functioning needs of the fireplace.
The size of the fireplace cavity, the design of the chimney
for effective venting should be determined. The availabil-
ity of the gas supply as well as electricity for the insert fan
must be confirmed.







4. Under no circumstances should this appliance be modified.
Parts removed for servicing should be replaced prior to
operating this appliance again.
5. Installation and any repairs to this appliance should be
carried out by a qualified installer, preferably NFI or WETT
(Canada) certified. A professional service person should
be contacted to inspect this appliance annually. Make it a
practice to have all of your gas appliances checked annually.
More frequent cleaning may be required due to excess lint
and dust from carpeting, bedding material, etc.
6. Control compartments, burners and air passages in this ap
-
pliance should be kept clean and free of dust and lint. Make
sure that the gas valve and pilot light are turned off before
you attempt to clean this unit.
7. The venting system (chimney) of this appliance should be
checked at least once a year and if needed your venting
system should be cleaned.
8. Keep the area around your appliance clear of combustible
materials, gasoline and other flammable vapor and liquids.
This appliance should not be used as a drying rack for cloth-
ing, nor should Christmas stockings or decorations be hung
in the area of it.
9. Under no circumstances should any solid fuels (wood, coal,
paper or cardboard etc.) be used in this appliance.
10. The flow of combustion and ventilation air must not be ob-
structed in any way.
11. These appliances are certified for installation in a solid
fuel burning fireplace unless using the model HEZC Zero
Clearance Kit. When the zero clearance kit is used, and the
appliance is installed directly on carpeting, vinyl tile or any
combustible material other than wood, the appliance must
be installed on a metal or wood panel extending the full
width and depth of the appliance.
12. This appliance requires adequate ventilation and combus
-
tion air to operate properly.
A125 / A132
Certified To
ANSI Z 21.88-2005 / CSA 2.33-2005
Vented Gas Fireplace Heaters