Filter
Top Products
Regency Z2510 WarmHearth6
Unit Dimensions
INSTALLATION
8) NEVER leave children unattended when
there is a fi re burning in the fi replace.
9) Allow the fi replace to cool before servicing.
Always shut off any electricity to the fi replace
while working on it. This will prevent any
possible electrical shock.
10) Regency is not responsible for any smok-
ing or related problems that may result
from the lack of adequate combustion
air. It is the responsibility of the installer
to ensure that adequate combustion air
has been provided for the fi replace.
11) Regency Industries Ltd. does not warranty
“smoke free” operation nor are we respon-
sible for inadequate system draft caused by
mechanical systems, general construction
conditions, inadequate chimney heights,
adverse wind conditions and/or unusual
environmental factors or conditions beyond
our control.
12) DO NOT use a fi replace insert or any other
product not specifi ed by Regency for use
with this fi replace.
13) Never, under any circumstances, install a
fi replace, chimney component or any ac-
cessories, supplied by Regency, that have
visible or suspected physical damage as a
result of handling or transportation. These
items should be inspected by a Regency
dealer or qualifi ed factory representative
to ensure safe condition. When in doubt,
consult your Regency dealer.
14) It is recommended that power is supplied
to the terminal block of the unit to allow for
the installation of blower components now
or at a future date.
READ BEFORE YOU INSTALL
THE REGENCY WARMHEARTH
HIGH EFFICIENCY EPA
CERTIFIED FIREPLACE
This installation manual will enable you to make
a safe, effi cient and dependable installation of
your fi replace and chimney system. Please
read and understand these instructions before
beginning your installation.
Do not alter or modify the fi replace or its
components under any circumstances. Any
modifi cation or alteration of the fi replace system,
including but not limited to the fi replace, chimney
components and accessories, may void the
warranty, listing and approvals of this system
and could result in an unsafe and potentially
dangerous installation.
PLEASE RETAIN THIS MANUAL FOR
FUTURE REFERENCE.
IMPORTANT: Please read and follow these
rules for safety.
1) Before starting your fi replace installation,
read these installation instructions carefully
to be sure you understand them in their
entirety. Failure to follow them could cause
a fi replace malfunction resulting in serious
injury and/or property damage.
2) Always check your local building codes.
The installation must comply with all local,
regional and state codes and regulations.
3) This model fi replace must be installed with
one of the chimney systems listed in the
Chimney Section in this manual. These
systems are intended for use as a residential
type appliance. The chimney must always
vent to the outside of the building.
4) To ensure a safe fi replace system and to
prevent the build-up of soot and creosote,
inspect and clean the fi replace and chimney
prior to use and periodically during the heat-
ing season.
5) Use solid fuel only. DO NOT use artifi cial logs
containing petroleum products, chemical
chimney cleaners, gas logs, gas lighters,
salt contaminated wood or fl ame colorants
in your fi replace. When using compressed
sawdust logs use only at 1/3 capacity since
these get very hot and expand.
6) DO NOT use charcoal or coal under any
circumstances.
7) NEVER use gasoline, gasoline-type lantern
fuel, kerosene, charcoal lighter fl uid, or any
liquid to start or “freshen up” a fi re in this
fi replace. Keep any fl ammable liquid a safe
distance from the fi replace.
DIMENSIONS AND
SPECIFICATIONS
The WarmHearth is a woodburning fi replace
featuring a self-contained heat-circulating
system and cast-iron door with large viewing
window. Options available are a Central Heating
System or an Internal Blower. A set of andirons
are installed in the fi rebox to properly position
the fi re, do not remove them.
Note: Illustrations shown refl ect “typical”
installations with nominal dimen-
sions and are for design and framing
reference only. Actual installations
may vary due to individual design
preferences. However, always main-
tain minimum clearances to combus-
tible materials and do not violate any
specifi c installation requirements.
The WarmHearth fi replace has been tested
and listed by Warnock Hersey Inc. to UL. 127
Standard for U.S. installations and ULC. S610
standard for Canadian installations. This unit
is intended for installation in conventional
homes and buildings of conventional con-
struction, not in mobile homes.
This fi replace system is designed for installation
in accordance with the National Fire Protection
Standard for chimneys, fi replaces and solid
fuel burning appliances; NFPA 211 and in ac-
cordance with codes such as the BOCA Basic
National Codes, the Standard Mechanical Code,
Uniform Building Codes, Canadian National
Building Codes or applicable local codes.
Emissions from burning wood or gas could
contain chemicals known to the State of Cali-
fornia to cause cancer, birth defects or other
reproductive harm.