Filter
Top Products
Page 39
Feature #24 Door Lock/Unlock Pulse Duration
(Factory Default Setting .8 Second)
This feature, for the installer’s use, offers the selection of a .8 second or a 3
second pulse duration of the system’s doorlock outputs. Certain vehicles have
power doorlocking systems which are vacuum operated, and thus require a
longer output pulse from the Crime Guard system. While use of this feature is
determined by the type of vehicle the system is installed in, this feature does save
the owners of such vehicles the added expense of a special adapter.
Programming Door Lock/Unlock Pulse Duration:
Follow Steps 1 to 4 on page 28; at Step 4 the Valet Switch will be pressed and
released twenty four times. The system’s response will be twenty four siren
chirps, and the Status Light flashing twenty four times, pausing, then repeating.
Within 10 seconds, press and release the transmitter/transceiver’s "Arm/Lock"
button to configure the doorlock pulse for .8 second (the siren will chirp once)
or the "Disarm/Unlock" button to configure the doorlock pulse for 3 seconds (the
siren will chirp twice).
Disarming the system with every press of that same button. When this feature
is programmed for “1 Button Operation”, the system’s operation with the
included transmitter and/or Echo pager is:
“Locked Lock” button = Arm or Disarm (alternates)
“Unlocked Lock button = Auxiliary #2 output
“II” button = Auxiliary #3 output
“III” button = nothing (open for other receiver unit)
“Locked Lock” & “Unlocked Lock” buttons together = remote start
Programming Transmitter 1 or 2 Button Operation:
Follow Steps 1 to 4 on page 28; at Step 4 the Valet Switch will be pressed and
released twenty three times. The system’s response will be twenty three siren
chirps, and the Status Light flashing twenty three times, pausing, then repeating.
Within 10 seconds, press and release the transmitter/transceiver’s "Arm/Lock"
button to configure the system for “1 Button Operation” (the siren will chirp
once) or the "Disarm/Unlock" button to configure the system for “2 Button
Operation” (the siren will chirp twice).
Feature #25 Double Unlock Pulse
(Factory Default Setting OFF)
This is another power door lock-related feature for the installer’s use; some
newer vehicles require a double pulse to remotely unlock the doors and/or to
disarm a factory-equipped security system.
To Disarm the System:
Press & Release the “Disarm/Unlock” Button ( )
THE SIREN WILL CHIRP
ONCE TO CONFIRM
DISARMING
REMOTE DISARMING BY TRANSMITTER OR TRANSCEIVER
THE PARKING AND
DOME LIGHTS WILL
ILLUMINATE
TO CONFIRM
DISARMING
Page 10
• Pressing “Disarm/Unlock” will disarm the system, leaving the doors locked,
stopping both system’s alarm condition (leaving it disarmed) and the
transceiver’s chirping.
• Pressing and releasing any of the three other buttons will simply stop the
transceiver’s chirping, but leave the security system still sounding in its
alarm state.
The remote transceiver will display the flashing icon indicating the violated zone,
while the system is disarmed, until the ignition switch is turned on.
There are three methods of Disarming the security system:
1- The first method is to press and release the transmitter or transceiver’s
“Disarm/Unlock” button to disarm the system. This is the normal method.
2- The second method is to press and release the transmitter or transceiver’s “II”
button twice within 5 seconds. This is “silent Disarming”.
3- The third method is for emergencies, should the transmitter become lost or
inoperable. This is the “Emergency Override”, and uses the ignition key and
the Valet Switch.
DISARMING THE SYSTEM
THE DOORS WILL UNLOCK;
Either All or Drivers*
With Driver’s Door Priority, again Press & Release the “Disarm/Unlock”
Button ( ) to unlock the remaining doors
J
*An optional doorlock interface, in either standard form or driver’s door priority form, must be installed
J