Filter
Top Products
While the system is in the Armed state:
• The Status Light will be flashing slowly Red to confirm that the system is
armed, and also serve as a visual deterrent.
• The starter interrupt circuit is engaged.
• All protected zones are being monitored for intrusion attempts.
Should an Activation into the Alarm Condition occur:
• The changing-tone electronic siren will loudly sound.
• The parking and interior lights will flash.
• The doors will lock,* regardless of their locked or unlocked status. This feature
is unique- if the system detects that a door is opened, it waits until the door is
closed before relocking it, denying the thief reentry.
An activated alarm condition has a duration of 30 seconds (60 is optional)
unless the system is disarmed using the transmitter, transceiver, or the Valet
Switch. If all protected zones are secure at the end of the alarm condition, the
system will stop and rearm automatically, ready to detect another entry attempt.
If a protected zone is still violated at the end of the alarm condition, the system
will reactivate for up to two additional alarm cycles. After the third alarm cycle
the system will automatically rearm and bypass the open zone until that zone
returns to a normal “non-violated” state.
• Once the system resets after it has been activated, upon disarming the audible
and visual confirmation will change to indicate the activation. This is the
“Activation Alert”, which is explained on pages 11-12.
The Echo Remote Transceiver’s reaction to the alarm condition:
If the remote transceiver was previously used to arm or operate the system, it
will react to an alarm activation, provided it is within range of the system. Upon
receiving a signal from the activated system, the transceiver will:
• The transceiver will start chirping, and continue chirping until any transceiver
button is pressed.
• An icon will start flashing, indicating which protected zone’s violation caused
the system’s alarm condition.
When silencing the transceiver’s alarm chirps, please note the differences of
pressing it’s buttons:
• Pressing “Arm/Lock” will rearm the system, stopping both system’s alarm
condition (leaving it armed) and the transceiver’s chirping.
SYSTEM ARMED & ACTIVATED
* An optional doorlock interface must be installed
Page 9Page 40
Feature #27 Gasoline Or Diesel Engine
(Factory Default Setting Gasoline)
This feature changes the system's timing of the ignition and starter output
sequence for remotely starting vehicles with a diesel engine.
Programming Gasoline or Diesel Engine:
Follow Steps 1 to 4 on page 28; at Step 4 the Valet Switch will be pressed and
released twenty seven times. The system’s response will be twenty seven siren
chirps, and the Status Light flashing twenty seven times, pausing, then repeating.
Within 10 seconds, press and release the transmitter/transceiver’s "Arm/Lock"
Feature #26 Total Closure Lock Output
(Factory Default Setting OFF)
If the vehicle is has an existing total closure feature, this programmable
feature gives the installer the option of interfacing the system to operate this
feature. Typically, this option would close all windows and the sunroof, in
addition to locking the doors, when arming the system. Consult with the in-
staller on this option, as the vehicle must be properly equipped to utilize this
system feature. Turning this feature on changes the door lock output pulse to a
28 second duration.
Note: When using this feature, upon Arming the system, should the “Disarm/
Unlock” button be pressed during the 28 second lock output period, the output
will stop only- the system will not Disarm. Pressing the button again will Disarm
the system, and at any time after the 28 second lock output period.
Programming Total Closure Lock Pulse:
Follow Steps 1 to 4 on page 28; at Step 4 the Valet Switch will be pressed and
released twenty six times. The system’s response will be twenty six siren chirps,
and the Status Light flashing twenty six times, pausing, then repeating. Within
10 seconds, press and release the transmitter/transceiver’s "Arm/Lock" button to
configure the 28 second door lock pulse for total closure (the siren will chirp
once) or the "Disarm/Unlock" button to configure the short door lock pulse (the
siren will chirp twice).
Programming Single or Double Unlock Pulse:
Follow Steps 1 to 4 on page 28; at Step 4 the Valet Switch will be pressed and
released twenty five times. The system’s response will be twenty five siren
chirps, and the Status Light flashing twenty five times, pausing, then repeating.
Within 10 seconds, press and release the transmitter/transceiver’s "Arm/Lock"
button to configure the double unlock pulse (the siren will chirp once) or the
"Disarm/Unlock" button to configure the single unlock pulse (the siren will chirp
twice).