Filter
Top Products
L NAPCO Security Systems
X GEM-P1664 Installation Instructions
WI1424A 1/06
Page 43
positive or negative temperature. If the temperature of 0 degrees is required, "negative zero" (-0) degrees must be used (+0 or an
empty location is not a valid temperature). To simulate the sensor module, a power supply can be connected to Zone 6 and set
from .55v to 3.05v to display the whole temperature range. Temperature values are read and updated every 5 seconds. To report
an outer limit temperature, the temperature must be out of limits for 2 seconds. To avoid false alarm reports, the limits have a
threshold of 5 degrees in the software. Two new logs have been created for temperature out of limits and restore. If the
G key
is depressed and held down for 2 seconds, the date will display for 5 seconds.
Test Timer; Cancel Next Test Timer Report on Any Report
The test timer schedule is programmed via the Easy Program Menu and using Napco's Quickloader Software. If "Test Timer" is
programmed, an automatic test report will be transmitted to the central station on the scheduled day(s) at the scheduled time. To
report test timer, select Report Test Time to Telco 1 or 3 and program a report code. Program the Test Timer reporting time and
day of the week. If "Cancel Next Test Timer Report on Any Report" is programmed, any report will cause the next test-timer
transmission to be aborted, however subsequent test-timer transmissions will report as scheduled. Do not program this feature in
UL installations.
Timeout
Specifies the length of time that an alarm, alert, or delay will remain active. See Time Selection.
Time Selection
The following times are programmable:
Time and Date (Keypad) in Dealer Program Mode
The Keypad Time and Date on the GEM-RP1CAe2/GEM-K1CA keypad may be set in Dealer Program Mode.
Time and Date (Keypad) in User Program Mode
When using an GEM-RP1CAe2/GEM-K1CA, the Time and Date may be set in the User Program Mode.
Time and Date Message Option
In the event of a complete power failure (AC and DC) and the loss of the system clock, when the system is re-powered, a message
'SET TIME / DATE" will be displayed on the GEM-RP1CAe2 keypad. The message will remain until the Time and Date have been
re-programmed.
Touch-tone Dialing Only; TouchTone Dialing with Rotary Backup
Select "TouchTone Dialing Only" if the subscriber has TouchTone service. TouchTone dialing is faster than rotary dialing, but not
always as reliable.
For the communicator to use TouchTone on all dial attempts, program TouchTone Dialing Only. To use TouchTone on the first
attempt with subsequent Rotary dial, program TouchTone Dialing with Rotary Backup. TouchTone Dialing Only will override
TouchTone Dialing with Rotary Backup if both are selected. Note that if Backup Reporting is also selected, the communicator will
alternate between TouchTone and rotary dial to reach Telephone 1, then Telephone 2. See Backup Report on Telco 2.
Trouble; Fire Trouble
An abnormal zone condition (a break in a normally-closed loop; a short on a normally-open loop; or either on an end-of-line-resistor
supervised loop) when disarmed.
Trouble on a Burglary Zone is automatically displayed at the keypad unless Disable Zone Fault Scrolling is programmed. If a
Burglary Zone is in trouble, it will go into alarm about 10 seconds after arming. However, if Auto Bypass is programmed, the keypad
will beep upon arming (does not apply to selective- or group-bypassed zones).
Glossary
TIME(1) UNITS MAX. PROG. TIME
PGM2 OUTPUT TIMEOUT MIN. UNTIMED(2)
PGM2 OUTPUT ACCESS CONTROL TIME SEC. 4 MIN., 15 SEC. (255 SEC.)
ALARM OUTPUT MIN. UNTIMED(1)(2)
PULSE-BURG OUTPUT MIN. UNTIMED(1)(2)
PGM1 OUTPUT MIN. UNTIMED(2)
ABORT DELAY SEC. 4 MIN., 15 SEC. (255 SEC.)(3)
CHIME TIME SEC. 63.25 SEC. (255 QTR-SEC.)(3)
AC-FAIL REPORT DELAY 10 MIN. 42 HR., 30 MIN. (2550 MIN.)
EXIT DELAY SEC. 4 MIN., 15 SEC. (255 SEC.)(4)
ENTRY DELAY 1 SEC. 4 MIN., 15 SEC. (255 SEC.)(4)
ENTRY DELAY 2 SEC. 4 MIN., 15 SEC. (255 SEC.)(4)
SENSOR WATCH HRS 254 HRS.
CANCEL WINDOW MIN. 254 MIN.
ZONE INTEGRATION TIME 10 MILLISECONDS 2.55 SEC.
ZONE ANDING TIME SEC. 255 SEC.