Napco Security Technologies GEM-P1664 Home Security System User Manual


 
X GEM-P1664 Installation Instructions
L NAPCO Security Systems
WI1424A 1/06
Page 40
external remote mounting, and one module may be used with the GEM-P1664 Control Panel. Use the RM3008, RB3008 or the
GEM-OUT8 for 16 independent programmable active low outputs for controlling 32 relay events, which can be assigned to any of the
16 available external outputs. Multiple relay events can drive the same external relay.
Relay Follows Zone
External Relays can be programmed to follow a zone. If values are entered in Time locations, the relay will time out after the
programmed time.
Remote Panic See Panic Zone
Report Digital Dialer Exit Error/Recent Closing
A Recent Closing transmission is sent if an alarm occurs within two (2) minutes after the expiration of the Exit Time. If the user num-
ber is available, it is included in the Recent Closing transmission. Note: Recent Closing transmissions are not sent for fire alarms.
Report Telco 1; Report Telco 3 (Double or Split Reporting)
Alarms, alarm restores, troubles and trouble restores may be selected individually for each zone. Violation of a zone selected to
report will communicate the code(s) selected for that zone to the central station.
Normally, Report Telco 1 is used to report to the central station. Report Telco 3 is used when certain zones will report to a different
receiver (split reporting); Report Telco 1 and Report Telco 3 are both used on the same zone to report to two receivers successively
(Double Reporting). (Double Reporting requires a successful report to Telco 1 before reporting to Telco 3). Also see Backup Report
on Telco 2.
Reset Day Zone with Arm/Disarm Only See Day Zone
Residential Fire
Prevents battery depletion during alarm. Must be programmed in Residential Fire Installations.
Security Bypass
Recommended for commercial applications, requires entry of a valid user code. A typical application would be a warehouse or ship-
ping terminal where the overhead doors are programmed for 24 hour protection and must be Bypassed to allow access, and then Un-
bypassed again. To activate this feature, DO NOT program Disable Code Required for EZ Bypass is Program BE (Bypass Enable)
for each user who is to have this ability.
To Security Bypass a zone:
1. Enter a code valid for bypass (Authority Level 1 or higher and Bypass option enabled), then press the
B button; BYPASS
ENABLED will display.
2. Press the
B button, then the zone number (or vice versa) to deactivate that zone. Similarly, a bypassed zone may be un-
bypassed using the same procedure. Note: When the panel is subsequently disarmed, all bypassed zones revert to unby-
passed zones (unless Disable Auto-Unbypass on Disarming is programmed or Interior Zones are programmed normally by-
passed).
It is not possible to Bypass/Unbypass Zones using the Directory Mode procedure.
Typically, any zone, other then a fire zone, will automatically be unbypassed when the panel is disarmed.
In order to unbypass a fire zone, follow procedures 1 through 4.
When a fire zone is bypassed, the panel will go into a fire trouble condition. It will also transmit the fire trouble to the CS, if pro-
grammed to do so.
Zones 1-9 are entered as 01 - 09.
Select Alarm Output for Keyfob Chirp
This feature is associated with Chirp Output on Keyfob Arm/Disarm. Normally the chirp on a keyfob arm/disarm is transmitted to
the PGM2 output. Selecting "Select Alarm Output for Keyfob Chirp" causes the "Bell" to chirp instead of the PGM2 upon remote arm-
ing.
Selective Bypass
Disable Code Required for EZ Bypass (Not for UL installations)
Any or all zones (1-64) programmed for Selective Bypass may be removed from the system, but each must be removed separately.
Refer to BYPASSING ZONES in Section 3 for operation. Security Bypass: Recommended for commercial applications, requires en-
try of a valid user code. EZ Bypass: Recommended for residential applications, is selected by programming Disable Code Entry for
EZ Bypass; this will permit bypassing/unbypassing zones without the need of entering a code (see EZ Bypass in Section 3). Do not
program this feature in high-security applications. When one or more zones is bypassed, the BYPASSED reminder on the GEM-
RP1CAe2 and GEM-K1CA keypads will display.
Glossary