Filter
Top Products
20
107569
UNVENTED NATURAL GAS FIREPLACE
For more information, visit www.desatech.com
NORMAL LIGHTING
INSTRUCTIONS
OPERATING
FIREPLACE
FOR YOUR SAFETY
READ BEFORE
LIGHTING
WARNING: If you do not fol-
low these instructions exactly, a
fire or explosion may result caus-
ing property damage, personal
injury or loss of life.
A. This appliance has a pilot which lights
automatically when using the sup-
plied wall switch or remote control.
If you have a power outage, the pilot
may be lighted by hand with push-
button piezo ignitor. When lighting
the pilot, the following warnings
must be followed.
B. BEFORE LIGHTING smell all
around the appliance area for gas. Be
sure to smell next to the floor because
some gas is heavier than air and will
settle on the floor.
WHAT TO DO IF YOU SMELL
GAS
• Do not try to light any appliance.
• Do not touch any electric switch;
do not use any phone in your building.
• Immediately call your gas supplier
from a neighbor’s phone. Follow
the gas supplier’s instructions.
• If you cannot reach your gas sup-
plier, call the fire department.
C. Electric Power Outage Only: Use only
your hand to turn the manual over-
ride handle on the gas control knob.
Never use tools. If the knob will not
turn by hand, don’t try to repair it,
call a qualified service technician or
gas supplier. Force or attempted re-
pair may result in a fire or explosion.
D. Do not use this appliance if any part
has been under water. Immediately
call a qualified service technician to
inspect the appliance and to replace
any part of the control system and
any gas control which has been un-
der water.
WARNING: You must operate
this heater with the fireplace
screen in place. Make sure fire-
place screen is in place before
running heater.
NOTICE: During initial operation
of new heater, burning logs will
give off a paper-burning smell.
Open damper or window to vent
smell. This will only last a few
hours.
1. STOP! Read the safety information,
in column 1.
2. Make sure equipment shutoff valve
is fully open.
3. Wait five (5) minutes to clear out any
gas. Smell for gas around heater and
near floor. If you smell gas, STOP!
Follow “B” in the safety information
on warnings plate. If you don’t smell
gas, go to the next step.
A. Using Supplied Wall Switch
1. Set manual ignition bypass switch on
the control panel to the OFF position
(automatic ignition position).
2. Press ON/OFF button. Hold for 6
seconds. Gas valve will open and elec-
tronic ignition will begin sparking to
light pilot. LED will light.
Note:
You may be running this
heater for the first time after connect-
ing to gas supply or at the start of
your heating season. If so, the ON/
OFF button may need to be pressed
again. This will allow air to bleed
from gas system. If several attempts
to light pilot fail, contact a qualified
service person or gas supplier for re-
pairs. Until repairs are made, light
and operate manually (see Manual
Lighting Instructions for Electric
Power Outage, page 21).
3. When pilot flame is lit, the thermo-
couple is heated by the flame. When
thermocouple becomes hot (5 to 15
seconds), main burner will automati-
cally light on high flame.
INSTALLATION
Continued
Figure 47 - Installing Fireplace Screen
WARNING: You must operate
this fireplace with the fireplace
screen in place. Make sure fire-
place screen is in place before
running fireplace.
Install fireplace screen by slipping notches
of fireplace screen over screws on front of
fireplace (see Figure 47).
INSTALLING SCREEN
Notches
Screws for Mounting Screen
INSTALLING BATTERY INTO
REMOTE
1. Locate slot at bottom of remote control
(see Figure 48). Firmly insert tool such as
a small screwdriver, butter knife, or dime
into the slot and lift up to remove cover.
2. Insert supplied battery into remote
control. Positive and negative are
marked inside remote control casing.
Note:
Remote will not function if bat-
tery is not installed correctly.
3. Slide tab on cover into remote housing
and snap cover back into place.
Figure 48 - Installing Battery
Positive
Negative
Tab
Cover
Remote
Control
Slot