Filter
Top Products
21
107569
OWNER’S MANUAL
For more information, visit www.desatech.com
ON
OFF
HI
LO
MANUAL
IGNITION
CAUTION: Do not try to adjust
heating levels by using the equip-
ment shutoff valve.
Figure 50 - Control Locations
Continued
4. To lower flame, push HI/LO button
on wall switch once.
Note:
This fireplace does not have a
pilot-only mode.
Automatic
Ignitor Electrode
Pilot
Burner
Figure 49 - Pilot
ON
OFF
HI
LO
MANUAL
IGNITION
Manual Ignition Bypass Switch
(Up is for Remote Control)
ON/OFF
Button
HI/LO
Button
Wall
Switch
OPERATING
FIREPLACE
Continued
B. Using Hand-Held Wireless
Remote Control
1. Set manual ignition bypass switch on
control panel to OFF position (auto-
matic ignition position).
2. Wait five (5) minutes to clear out any
gas. Smell for gas around heater and
near floor. If you smell gas, STOP!
Follow “B” in the safety information
on warnings plate. If you don’t smell
gas, go to the next step.
TO TURN OFF GAS
TO APPLIANCE
Shutting Off Heater - Wall
Switch
Push ON/OFF button on wall switch once.
Shutting Off Heater - Wireless
Remote Control
Point remote control toward lower front
of fireplace and push both buttons at the
same time.
MANUAL LIGHTING
INSTRUCTIONS
FOR ELECTRICAL
POWER OUTAGE
WARNING: You must operate
this heater with the fireplace
screen in place. Make sure fire-
place screen is in place before
running heater.
NOTICE: During initial operation
of new heater, burning logs will
give off a paper-burning smell.
Open damper or window to vent
smell. This will only last a few
hours.
Because this fireplace has an electronic
ignition system, in the event there is a loss
of power, it will be necessary to manually
light the pilot with the piezo ignitor. After
the pilot is lit, the main burner will light
automatically.
1. Follow steps 1 through 3 under Nor-
mal Lighting Instructions, page 20.
2. Set manual ignition bypass switch on
control panel to ON position (manual
ignition position). See Figure 51.
3. The pilot is attached to the rear of
the front burner. You will be able to
see the pilot and spark electrode
without removing the screen or logs.
4. Place the magnetic manual override
handle, provided with this unit, on
the end of the gas valve stem (see Fig-
ure 51).
3. Point remote control toward the
lower front of fireplace and push
both buttons at the same time. Hold
for 6 seconds. The gas valve will open
and electronic ignition will begin
sparking to light the pilot.
Note:
Yo u
will be able to hear a clicking sound
during this process. LED on wall
switch will light.
Note:
You may be running this
heater for the first time after connect-
ing to gas supply or at the start of
your heating season. If so, the ON
button may need to be pressed again.
This will allow air to bleed from gas
system. If several attempts to light
pilot fail, contact a qualified service
person or gas supplier for repairs.
Until repairs are made, light and op-
erate manually (see Manual Lighting
Instructions for Electrical Power Out-
age, pages 20 and 21).
4. When pilot flame is lit, the thermo-
couple is heated by the flame. When
thermocouple becomes hot (5 to 15
seconds), main burner will automati-
cally light on high flame.
5. To lower flame, point remote control
toward lower front of fireplace and
push HI/LO button once.
Note:
This fireplace does not have a
pilot-only mode.
Figure 51 - Control Locations
Manual Ignition
Bypass Switch
(Down is ON)
Magnetic
Manual Override
Handle
ON/OFF
Button
HI/LO
Button
Piezo
Ignitor
Wall
Switch
Gas
Valve
Manual
Ignitor
Electrode
LED
LED
LED